VOLVO
ECM-P045912 - Evaporative Emission System Purge Control Valve Circuit High. General Electrical Failures. Circuit short to battery
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
7 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Modelle nach Baujahr und Motor anzeigen (20)
- Volvo S60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Nur Motor: B4204T6
- Volvo S80 (2007–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Nur Motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Nur Motor: B4164T
- Volvo V40 (2013–)2013Nur Motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Nur Motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B4164T
- Volvo V60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Nur Motor: B4204T6
- Volvo V70 (2008–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Nur Motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Nur Motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Nur Motor: B4204T6
- Volvo XC60 (2009–)2011–2012Nur Motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Nur Motor: B4204T7
Was bedeutet der Fehlercode?
The engine control module has registered that the signal from the EVAP valve is too high. The code is general and concerns an electrical fault. The causes are a signal wire short-circuited to supply voltage or a damaged EVAP valve.
Mögliche Ursachen
- The signal wire is short-circuited to supply voltage
- Damaged EVAP valve
Was Sie tun können
- 1Check that the connector at the EVAP valve is fully seated and free from corrosion
- 2Look for chafing or pinch damage on the wire between the EVAP valve and the engine control module
- 3Use a multimeter to check that the EVAP valve is electrically intact. An open circuit or short inside the valve shows that it is damaged
- 4With a multimeter, check that the signal wire between the engine control module and the EVAP valve has no contact with supply voltage
- 5Replace a damaged EVAP valve, clear the code and road test. If the fault remains, have a workshop with diagnostic equipment check the wiring
Symptome, die Sie bemerken können1
- The malfunction indicator (check engine) light comes on or behaves abnormally
Was der Fehler beeinflussen kann1
- Control with two oxygen sensors (lambda sensors) is disabled
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.