VOLVO
ECM-P061B64 - Internal Control Module Torque Calculation Performance. Algorithm Based Failures. Signal plausibility failure
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
10 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Modelle nach Baujahr und Motor anzeigen (44)
- Volvo S60 (2011–)2011Nur Motor: B6304T4
- Volvo S60 (2011–)2012Nur Motor: B6304T4, D4162T
- Volvo S60 (2011–)2013Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14, B6304T4, D4162T
- Volvo S60 (2011–)2014Alle Motoren außer: B4164T, B4164T2, B4164T3, B4204T7, D5204T3, D5204T7, D5244T11, D5244T15
- Volvo S60 (2011–)2015Alle Motoren außer: B4164T, B4164T2, B4164T3, D5204T3, D5204T7, D5244T11, D5244T15, D5244T23
- Volvo S80 (2007–)2007Nur Motor: B6324S, B8444S
- Volvo S80 (2007–)2008–2009Nur Motor: B6304T2, B6324S, B8444S
- Volvo S80 (2007–)2010Nur Motor: B6304T2, B6324S, B6324S2, B8444S
- Volvo S80 (2007–)2011Nur Motor: B6304T4, B6324S4, B6324S5, B8444S
- Volvo S80 (2007–)2012Nur Motor: B6304T4, B6324S4, B6324S5, D4162T
- Volvo S80 (2007–)2013Nur Motor: B5254T12, B5254T14, B6304T4, B6324S4, B6324S5, D4162T
- Volvo S80 (2007–)2014Alle Motoren außer: B4164T, B4164T2, B4204T6, B4204T7, D5204T3, D5204T7, D5244T11, D5244T15
- Volvo S80 (2007–)2015Alle Motoren außer: B4164T, D5204T3, D5244T15
- Volvo V40 (2013–)2013Alle Motoren außer: B4164T, B4164T3, D5204T4, D5204T6
- Volvo V40 (2013–)2014Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14, D4162T
- Volvo V40 (2013–)2015Alle Motoren außer: B4164T, B4164T3, B4164T4, D5204T6
- Volvo V40 Cross Country (2013–)2013–2014Alle Motoren außer: B4164T, D5204T4, D5204T6
- Volvo V40 Cross Country (2013–)2015Alle Motoren außer: B4164T, D5204T6
- Volvo V60 (2011–)2011Nur Motor: B6304T4
- Volvo V60 (2011–)2012Nur Motor: B6304T4, D4162T
- Volvo V60 (2011–)2013Nur Motor: B5204T8, B5204T9, B6304T4, D4162T
- Volvo V60 (2011–)2014Nur Motor: B4204T11, B4204T12, B4204T15, B4204T9, B5204T8, B5204T9, B5254T12, B6304T4, D4162T, D4204T5
- Volvo V60 (2011–)2015Nur Motor: B4204T11, B4204T12, B4204T15, B4204T9, B5204T9, B5254T12, B6304T3, B6304T4, B6304T5, D4162T, D4204T5
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008–2009Nur Motor: B6304T2, B6324S
- Volvo V70 (2008–)2010Nur Motor: B6304T2, B6324S, B6324S2
- Volvo V70 (2008–)2011Nur Motor: B6304T4, B6324S5
- Volvo V70 (2008–)2012Nur Motor: B6304T4, B6324S5, D4162T
- Volvo V70 (2008–)2013Nur Motor: B5204T9, B6304T4, B6324S5, D4162T
- Volvo V70 (2008–)2014Nur Motor: B4204T11, B5204T9, B6304T4, B6324S5, D4162T, D4204T5
- Volvo V70 (2008–)2015Nur Motor: B4204T11, B5204T9, B6304T4, D4162T, D4204T5
- Volvo XC60 (2009–)2009Nur Motor: B6304T2
- Volvo XC60 (2009–)2010Nur Motor: B6304T2, B6324S, B6324S2
- Volvo XC60 (2009–)2011–2013Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo XC60 (2009–)2014Alle Motoren außer: B4204T7, D5204T3, D5204T7, D5244T11, D5244T12, D5244T15, D5244T17
- Volvo XC60 (2009–)2015Alle Motoren außer: B4204T7, D5204T3, D5204T7, D5244T11, D5244T12, D5244T15, D5244T17, D5244T23
- Volvo XC70 (2008–)2008Nur Motor: B6324S
- Volvo XC70 (2008–)2009Nur Motor: B6304T2, B6324S
- Volvo XC70 (2008–)2010Nur Motor: B6304T2, B6324S, B6324S2
- Volvo XC70 (2008–)2011–2013Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2014–2015Nur Motor: B4204T11, B6304T4, B6324S4, B6324S5, D4204T5
- Volvo XC90 (2003–)2007–2010Nur Motor: B6324S
- Volvo XC90 (2003–)2011–2012Nur Motor: B6324S5
- Volvo XC90 (2003–)2013–2014Alle Motoren außer: B5254T9
Was bedeutet der Fehlercode?
The engine control module works out engine torque in two different ways and compares the results, and the fault is set when the two results differ too much from each other. The fault is checked in certain driving conditions, including idling, coasting and high engine load. The code is set first in the brake control module or the central electronics module (BCM/CEM), and it cannot be cleared until the faults there are remedied.
Mögliche Ursachen
- Fault in the brake control module (BCM), which should be traced first
- CAN-related fault codes in the central electronic module (CEM), or open circuit in the CAN wiring to it
- Contact resistance or oxidation in connectors
- Air leak after the mass air flow sensor or in the intake manifold after the throttle unit
- Damaged throttle unit, mass air flow sensor, air pressure sensor, coolant temperature sensor, impulse sensor or VVT unit
- Damaged turbocharger or turbo control valve, or damaged engine control module (ECM)
Was Sie tun können
- 1Have a workshop read the BCM fault codes first and then the CEM codes. Do not work on the braking system yourself
- 2Check that the connectors at the throttle unit and the mass air flow sensor are secure and free from oxidation
- 3Look for air leaks in the intake manifold after the mass air flow sensor and the throttle unit
- 4If you have a diagnostic tool: read the engine control fault codes after the other faults are remedied, and clear this code only once it is no longer active
- 5If the fault remains after these checks: have a workshop check the engine control module
Symptome, die Sie bemerken können4
- Text message in the information display, together with a warning symbol
- The engine lacks power, even when pulling away from standstill
- The engine hesitates, surges or runs jerkily during acceleration, deceleration or steady speed, sometimes or all the time
- The cruise control does not work at all
Was der Fehler beeinflussen kann3
- Engine torque is limited, among other ways by fuel shut-off or the throttle position
- Traction control stops working
- Vehicle performance is restricted if the fault stays present for a long time
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.