VOLVO
ECM-P086B00 - Neutral Position Sensor "A" Circuit Range/Performance. General Failure Information. No sub type information
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
11 ModelleC30 (2007–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V70 (2008–), XC60 (2009–), XC70 (2008–)
Modelle nach Baujahr und Motor anzeigen (33)
- Volvo C30 (2007–2013)2011–2013Nur Motor: D4162T
- Volvo S40 (2004–2013)2011–2012Nur Motor: D4162T
- Volvo S60 (2011–)2011Nur Motor: B4164T, B4164T3, D4162T
- Volvo S60 (2011–)2012Alle Motoren außer: B4204T7, B5254T5, B6304T4
- Volvo S60 (2011–)2013Alle Motoren außer: B4204T7, B5204T8, B5204T9, B5254T12, B5254T14, B6304T4
- Volvo S60 (2011–)2014Nur Motor: B4164T, B4164T2, B4164T3, D4162T, D4204T5, D5204T3, D5204T7, D5244T11, D5244T15
- Volvo S60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3, D4162T, D4204T5, D5204T3, D5204T7, D5244T11, D5244T15, D5244T23
- Volvo S80 (2007–)2011Nur Motor: B4164T
- Volvo S80 (2007–)2012Nur Motor: B4164T, B4164T2, D4162T, D5204T3, D5244T11, D5244T15
- Volvo S80 (2007–)2013Nur Motor: B4164T, B4164T2, D4162T, D5204T3, D5204T7, D5244T11, D5244T15
- Volvo S80 (2007–)2014Nur Motor: B4164T, B4164T2, D4162T, D4204T5, D5204T3, D5204T7, D5244T11, D5244T15
- Volvo S80 (2007–)2015Nur Motor: B4164T, D4162T, D4204T5, D5204T3, D5244T15
- Volvo V40 (2013–)2013–2014Alle Motoren außer: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V40 (2013–)2015Alle Motoren außer: B4204T11, B5204T8, B5204T9
- Volvo V40 Cross Country (2013–)2013–2014Nur Motor: B4164T, D4162T, D5204T4, D5204T6
- Volvo V40 Cross Country (2013–)2015Nur Motor: B4164T, D4162T, D4204T14, D5204T6
- Volvo V50 (2004–2013)2011–2012Nur Motor: D4162T
- Volvo V60 (2011–)2011Nur Motor: B4164T, B4164T3, D4162T
- Volvo V60 (2011–)2012Alle Motoren außer: B4204T7, B6304T4
- Volvo V60 (2011–)2013Alle Motoren außer: B4204T7, B5204T8, B5204T9, B6304T4
- Volvo V60 (2011–)2014Alle Motoren außer: B4204T11, B4204T12, B4204T15, B4204T7, B4204T9, B5204T8, B5204T9, B5254T12, B6304T4
- Volvo V60 (2011–)2015Alle Motoren außer: B4204T11, B4204T12, B4204T15, B4204T9, B5204T9, B5254T12, B6304T3, B6304T4, B6304T5
- Volvo V70 (2008–)2011Nur Motor: B4164T
- Volvo V70 (2008–)2012Alle Motoren außer: B4204T7, B5254T10, B6304T4, B6324S5
- Volvo V70 (2008–)2013Alle Motoren außer: B4204T7, B5204T9, B6304T4, B6324S5
- Volvo V70 (2008–)2014Alle Motoren außer: B4204T11, B4204T7, B5204T9, B6304T4, B6324S5
- Volvo V70 (2008–)2015Alle Motoren außer: B4204T11, B5204T9, B6304T4
- Volvo XC60 (2009–)2012Nur Motor: D5204T3, D5244T11, D5244T15, D5244T17
- Volvo XC60 (2009–)2013Alle Motoren außer: B4204T7, B6304T4, B6324S4, B6324S5
- Volvo XC60 (2009–)2014Nur Motor: D4204T5, D5204T3, D5204T7, D5244T11, D5244T12, D5244T15, D5244T17
- Volvo XC60 (2009–)2015Nur Motor: D4204T5, D5204T3, D5204T7, D5244T11, D5244T12, D5244T15, D5244T17, D5244T23
- Volvo XC70 (2008–)2012–2013Alle Motoren außer: B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2014–2015Alle Motoren außer: B4204T11, B6304T4, B6324S4, B6324S5
Was bedeutet der Fehlercode?
Neutral position sensor A measures the angle through which the gear lever turns the input shaft to the gearbox. During a gear change its voltage should change in a set pattern, but here it does not change at all or varies only within a small range. There is a main sensor and a backup redundancy sensor, and the fault concerns the main sensor's signal.
Mögliche Ursachen
- Loose contact or oxidation in the connector
- Short circuit or break in the wiring to the sensor
- Sensor incorrectly fitted to the gearbox
- Damaged link arm that the sensor is attached to
- Magnet damaged or in the wrong position
- Damaged neutral position sensor
Was Sie tun können
- 1Check that the fuses are intact. The locations are shown in the instruction manual or on the fuse list
- 2Check that the connector at the neutral position sensor is firmly seated and free from looseness and oxidation
- 3Check that the link arm and sensor are firmly fixed and undamaged, and that the sensor is correctly positioned on the gearbox
- 4Use a multimeter to check that the signal wire to the sensor has no break and is not shorted to earth
- 5If you have a diagnostic tool, check in live data that the sensor value changes clearly as the gear lever is moved between positions on a test drive
- 6If the fault remains, have a workshop check the sensor and its magnet
Symptome, die Sie bemerken können3
- Automatic engine stop-start does not work while driving
- Automatic engine stop-start does not work at idle
- Starting and auto-start do not work
Was der Fehler beeinflussen kann1
- The automatic engine stop-start function is switched off
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.