VOLVO
ECM-P086E00 - Neutral Position Sensor "A" Circuit Intermittent/Erratic. General Failure Information. No sub type information
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
11 ModelleC30 (2007–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V70 (2008–), XC60 (2009–), XC70 (2008–)
Modelle nach Baujahr und Motor anzeigen (29)
- Volvo C30 (2007–2013)2011–2013Nur Motor: D4162T
- Volvo S40 (2004–2013)2011–2012Nur Motor: D4162T
- Volvo S60 (2011–)2011Nur Motor: B4164T, B4164T3, D4162T
- Volvo S60 (2011–)2012Alle Motoren außer: B4204T7, B5254T5, B6304T4
- Volvo S60 (2011–)2013–2014Alle Motoren außer: B4204T7, B5204T8, B5204T9, B5254T12, B5254T14, B6304T4
- Volvo S60 (2011–)2015Alle Motoren außer: B5204T8, B5204T9, B5254T12, B5254T14, B6304T3, B6304T4, B6304T5
- Volvo S80 (2007–)2011Nur Motor: B4164T
- Volvo S80 (2007–)2012Nur Motor: B4164T, B4164T2, D4162T, D5204T3, D5244T11, D5244T15
- Volvo S80 (2007–)2013Nur Motor: B4164T, B4164T2, D4162T, D5204T3, D5204T7, D5244T11, D5244T15
- Volvo S80 (2007–)2014Alle Motoren außer: B4204T6, B4204T7, B5254T12, B5254T14, B6304T4, B6324S4, B6324S5
- Volvo S80 (2007–)2015Alle Motoren außer: B6304T4, B6324S4, B6324S5
- Volvo V40 (2013–)2013–2014Alle Motoren außer: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V40 (2013–)2015Alle Motoren außer: B5204T8, B5204T9
- Volvo V40 Cross Country (2013–)2013–2014Nur Motor: B4164T, D4162T, D5204T4, D5204T6
- Volvo V40 Cross Country (2013–)2015Alle Motoren außer: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V50 (2004–2013)2011–2012Nur Motor: D4162T
- Volvo V60 (2011–)2011Nur Motor: B4164T, B4164T3, D4162T
- Volvo V60 (2011–)2012Alle Motoren außer: B4204T7, B6304T4
- Volvo V60 (2011–)2013Alle Motoren außer: B4204T7, B5204T8, B5204T9, B6304T4
- Volvo V60 (2011–)2014Alle Motoren außer: B4204T7, B5204T8, B5204T9, B5254T12, B6304T4
- Volvo V60 (2011–)2015Alle Motoren außer: B5204T9, B5254T12, B6304T3, B6304T4, B6304T5
- Volvo V70 (2008–)2011Nur Motor: B4164T
- Volvo V70 (2008–)2012Alle Motoren außer: B4204T7, B5254T10, B6304T4, B6324S5
- Volvo V70 (2008–)2013–2014Alle Motoren außer: B4204T7, B5204T9, B6304T4, B6324S5
- Volvo V70 (2008–)2015Alle Motoren außer: B5204T9, B6304T4
- Volvo XC60 (2009–)2012Nur Motor: D5204T3, D5244T11, D5244T15, D5244T17
- Volvo XC60 (2009–)2013–2014Alle Motoren außer: B4204T7, B6304T4, B6324S4, B6324S5
- Volvo XC60 (2009–)2015Alle Motoren außer: B4204T7, B5204T9, B5254T12, B5254T14, B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2012–2015Alle Motoren außer: B6304T4, B6324S4, B6324S5
Was bedeutet der Fehlercode?
The engine control module adapts to the gear lever positions while driving, using the voltage levels that the neutral position sensor gives for high and low gear. The code is set when these levels vary too much for the adaptation to be carried out. It therefore indicates that the sensor signal is uneven or erratic.
Mögliche Ursachen
- Neutral position sensor adaptation not reset after work on the gearbox
- Loose contact or oxidation in the connector
- Short circuit or break in the wiring to the sensor
- Sensor incorrectly fitted to the gearbox
- Damaged link arm that the sensor is attached to
- Damaged neutral position sensor
Was Sie tun können
- 1Has any work recently been done on the gearbox? If so, the adaptation may need resetting, which is a job for a workshop
- 2Check that the fuses are intact. The locations are shown in the instruction manual or on the fuse list
- 3Check that the connector at the neutral position sensor is firmly seated and free from looseness and oxidation
- 4Check that the link arm and sensor are firmly fixed and undamaged
- 5Use a multimeter to check that the signal wire to the sensor has no break and is not shorted to earth
- 6If you have a diagnostic tool, check in live data that the sensor value changes smoothly as the gear lever is moved, with no jumps between positions
Symptome, die Sie bemerken können3
- Automatic engine stop-start does not work while driving
- Automatic engine stop-start does not work at idle
- Starting and auto-start do not work
Was der Fehler beeinflussen kann1
- The automatic engine stop-start function is switched off
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.