VOLVO
ECM-P151C68 - Idle Speed Control - RPM Higher Than Expected. Algorithm Based Failures. Event information
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
10 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Modelle nach Baujahr und Motor anzeigen (27)
- Volvo S60 (2011–)2011–2012Nur Motor: B6304T4
- Volvo S60 (2011–)2013–2014Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14, B6304T4
- Volvo S60 (2011–)2015Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14, B6304T3, B6304T4, B6304T5
- Volvo S80 (2007–)2007Nur Motor: B6324S, B8444S
- Volvo S80 (2007–)2008–2009Nur Motor: B6304T2, B6324S, B8444S
- Volvo S80 (2007–)2010Nur Motor: B6324S2
- Volvo S80 (2007–)2011–2015Nur Motor: B6324S4
- Volvo V40 (2013–)2013–2014Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V40 (2013–)2015Nur Motor: B5204T8, B5204T9
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V60 (2011–)2011–2012Nur Motor: B6304T4
- Volvo V60 (2011–)2013Nur Motor: B5204T8, B5204T9, B6304T4
- Volvo V60 (2011–)2014Nur Motor: B5204T8, B5204T9, B5254T12, B6304T4
- Volvo V60 (2011–)2015Nur Motor: B5204T9, B5254T12, B6304T3, B6304T4, B6304T5
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008–2009Nur Motor: B6304T2, B6324S
- Volvo V70 (2008–)2010Nur Motor: B6324S2
- Volvo XC60 (2009–)2009Nur Motor: B6304T2
- Volvo XC60 (2009–)2010Nur Motor: B6304T2, B6324S2
- Volvo XC60 (2009–)2011–2014Nur Motor: B6304T4, B6324S4
- Volvo XC60 (2009–)2015Nur Motor: B5204T9, B5254T12, B5254T14, B6304T4, B6324S4
- Volvo XC70 (2008–)2008Nur Motor: B6324S
- Volvo XC70 (2008–)2009Nur Motor: B6304T2, B6324S
- Volvo XC70 (2008–)2010Nur Motor: B6324S2
- Volvo XC70 (2008–)2011–2015Nur Motor: B6324S4
- Volvo XC90 (2003–)2007–2010Nur Motor: B6324S
- Volvo XC90 (2003–)2011–2014Nur Motor: B6324S5
Was bedeutet der Fehlercode?
The code is event controlled and therefore does not show a fault in the engine control module. It is set when the engine's starting speed has been outside the limit for a certain time. The code does not need to be corrected and disappears when the conditions no longer apply.
Mögliche Ursachen
- No repair is needed; the code only shows that the starting speed has been outside the limit
Was Sie tun können
- 1Check that the engine starts without delay and runs smoothly after starting.
- 2Clear the code and start the engine again. If the code does not return, it is gone.
- 3If the code returns together with a starting problem, have a workshop check the engine and the idle speed control.
Symptome, die Sie bemerken können1
- No noticeable symptoms for the driver
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.