VOLVO
ECM-P212200 - Throttle/Pedal Position Sensor/Switch D Circuit Low. General Failure Information. No sub type information
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Dieser Fehlercode hat je nach Modell, Modelljahr oder Motor unterschiedliche Bedeutungen. Wählen Sie die Bedeutung, die für Ihr Fahrzeug gilt.
Gilt für folgende Modelle:
14 ModelleC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Modelle nach Baujahr und Motor anzeigen (42)
- Volvo C30 (2007–2013)2011–2013Nur Motor: D5204T, D5204T5
- Volvo C70 (2006–2013)2011Nur Motor: D5204T, D5204T5
- Volvo C70 (2006–2013)2012–2013Alle Motoren außer: B5254T7
- Volvo S40 (2004–2013)2011–2012Nur Motor: D5204T, D5204T5
- Volvo S60 (2011–)2011Nur Motor: B6304T4, D5204T2, D5244T10
- Volvo S60 (2011–)2012Nur Motor: B6304T4, D5204T3, D5244T11, D5244T15
- Volvo S60 (2011–)2013Alle Motoren außer: B4164T, B4164T2, B4164T3, B4204T7, D4162T
- Volvo S60 (2011–)2014Alle Motoren außer: B4164T, B4164T2, B4164T3, B4204T7, D4162T, D4204T5
- Volvo S60 (2011–)2015Alle Motoren außer: B4164T, B4164T2, B4164T3, D4162T, D4204T5
- Volvo S80 (2007–)2009Nur Motor: D5244T10
- Volvo S80 (2007–)2010Nur Motor: B6304T2, B6324S, B6324S2, B8444S, D5244T10, D5244T14, D5244T19
- Volvo S80 (2007–)2011Nur Motor: B6304T4, B6324S4, B6324S5, B8444S, D5204T2, D5244T10
- Volvo S80 (2007–)2012Nur Motor: B6304T4, B6324S4, B6324S5, D5204T3, D5244T11, D5244T15
- Volvo S80 (2007–)2013Alle Motoren außer: B4164T, B4164T2, B4204T6, B4204T7, D4162T
- Volvo S80 (2007–)2014Alle Motoren außer: B4164T, B4164T2, B4204T6, B4204T7, D4162T, D4204T5
- Volvo S80 (2007–)2015Alle Motoren außer: B4164T, D4162T, D4204T5
- Volvo V40 (2013–)2013Alle Motoren außer: B4164T, B4164T3, D4162T
- Volvo V40 (2013–)2014Alle Motoren außer: B4164T, B4164T3, B4164T4, D4162T
- Volvo V40 (2013–)2015Nur Motor: B4204T11, B5204T8, B5204T9, D5204T6
- Volvo V40 Cross Country (2013–)2013–2014Alle Motoren außer: B4164T, D4162T
- Volvo V40 Cross Country (2013–)2015Alle Motoren außer: B4164T, D4162T, D4204T14
- Volvo V50 (2004–2013)2011–2012Nur Motor: D5204T, D5204T5
- Volvo V60 (2011–)2011Nur Motor: B6304T4, D5204T2, D5244T10
- Volvo V60 (2011–)2012Nur Motor: B6304T4, D5204T3, D5244T11, D5244T15
- Volvo V60 (2011–)2013Alle Motoren außer: B4164T, B4164T2, B4164T3, B4204T7, D4162T
- Volvo V60 (2011–)2014Alle Motoren außer: B4164T, B4164T2, B4164T3, B4204T7, D4162T, D4204T5
- Volvo V60 (2011–)2015Alle Motoren außer: B4164T, B4164T2, B4164T3, D4162T, D4204T5
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2009Nur Motor: D5244T10
- Volvo V70 (2008–)2010Nur Motor: B6304T2, B6324S, B6324S2, D5244T10, D5244T14, D5244T19
- Volvo V70 (2008–)2011Nur Motor: B6304T4, B6324S5, D5204T2, D5244T10
- Volvo V70 (2008–)2012Nur Motor: B6304T4, B6324S5, D5204T3, D5244T11, D5244T15
- Volvo V70 (2008–)2013Alle Motoren außer: B4164T, B4164T2, B4204T7, D4162T
- Volvo V70 (2008–)2014Alle Motoren außer: B4164T, B4164T2, B4204T7, D4162T, D4204T5
- Volvo V70 (2008–)2015Alle Motoren außer: B4164T, B4164T2, D4162T, D4204T5
- Volvo XC60 (2009–)2010Alle Motoren außer: B4204T6
- Volvo XC60 (2009–)2011–2012Alle Motoren außer: B4204T6, B4204T7
- Volvo XC60 (2009–)2013Alle Motoren außer: B4204T7
- Volvo XC60 (2009–)2014–2015Alle Motoren außer: B4204T7, D4204T5
- Volvo XC70 (2008–)2010–2013
- Volvo XC70 (2008–)2014–2015Alle Motoren außer: D4204T5
- Volvo XC90 (2003–)2011–2014Nur Motor: B6324S5
Was bedeutet der Fehlercode?
The engine control module monitors the accelerator pedal position sensor. The code is set when the PWM signal from the sensor has too low a frequency. The fault may come from an open or shorted signal or supply wire, from poor contact, or from a damaged pedal position sensor.
Mögliche Ursachen
- An open circuit in the signal wire
- The signal wire is short-circuited to ground
- The signal wire is short-circuited to supply voltage
- The supply wire is short-circuited to ground or supply voltage
- Contact resistance and oxidation in the connections
- Damaged accelerator pedal position sensor
Was Sie tun können
- 1Check that the fuses are intact
- 2Read the code with the ignition on and see whether it is still active
- 3Check the connectors at the pedal sensor and the engine control module for loose contacts and oxidation
- 4Look for breaks and chafing in the signal and supply wires, and use a multimeter to confirm they are not shorted to ground or supply voltage
- 5If the fault remains, have a workshop with diagnostic equipment decide whether the pedal sensor needs replacing
Symptome, die Sie bemerken können4
- A text message and a warning symbol appear in the display
- The engine hesitates or surges, and it is unclear when
- A message appears in the information display
- The accelerator pedal is ignored during braking
Was der Fehler beeinflussen kann3
- The control module switches over to the analogue signal sent via CAN
- When the brake pedal is pressed at the same time, the value for the released throttle position is used
- Performance is limited if the fault persists for a long time
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.