VOLVO
ECM-P213862 - Throttle/Pedal Position Sensor/Switch D / E Voltage Correlation. Algorithm Based Failures. Signal compare failure
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
10 ModelleC30 (2007–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V70 (2008–), XC60 (2009–)
Modelle nach Baujahr und Motor anzeigen (26)
- Volvo C30 (2007–2013)2011–2013Nur Motor: D4162T
- Volvo S40 (2004–2013)2011–2012Nur Motor: D4162T
- Volvo S60 (2011–)2011Alle Motoren außer: B5254T5, B6304T4, D5204T2, D5244T10
- Volvo S60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7, D4162T
- Volvo S60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3, D4162T
- Volvo S80 (2007–)2008–2009Nur Motor: D4204T
- Volvo S80 (2007–)2010Nur Motor: B4204T6, D4204T
- Volvo S80 (2007–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Nur Motor: B4164T, B4164T2, B4204T6, B4204T7, D4162T
- Volvo S80 (2007–)2015Nur Motor: B4164T, D4162T
- Volvo V40 (2013–)2013Nur Motor: B4164T, B4164T3, D4162T
- Volvo V40 (2013–)2014–2015Nur Motor: B4164T, B4164T3, B4164T4, D4162T
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B4164T, D4162T
- Volvo V50 (2004–2013)2011–2012Nur Motor: D4162T
- Volvo V60 (2011–)2011Alle Motoren außer: B6304T4, D5204T2, D5244T10
- Volvo V60 (2011–)2012Alle Motoren außer: B6304T4, D5204T3, D5244T11, D5244T15
- Volvo V60 (2011–)2013–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7, D4162T
- Volvo V60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3, D4162T
- Volvo V70 (2008–)2008–2009Nur Motor: D4204T
- Volvo V70 (2008–)2010Nur Motor: B4204T6, D4204T
- Volvo V70 (2008–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Nur Motor: B4164T, B4164T2, B4204T7, D4162T
- Volvo V70 (2008–)2015Nur Motor: B4164T, B4164T2, D4162T
- Volvo XC60 (2009–)2010Nur Motor: B4204T6
- Volvo XC60 (2009–)2011–2012Nur Motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Nur Motor: B4204T7
Was bedeutet der Fehlercode?
The engine control module (ECM) compares the analogue pedal signal, which travels via the central electronic module (CEM) over CAN, with the PWM signal that runs directly to the ECM. The code is set when the two signals do not follow each other. The fault may lie in the pedal sensor, its connectors or CEM.
Mögliche Ursachen
- Contact resistance or oxidation in the connections
- Fault in the CAN communication between the engine control module and the central electronic module (CEM)
- Fault in the pedal sensor PWM signal
- Fault in the analogue pedal sensor signal
- Damaged accelerator pedal sensor
- Fault in the central electronic module (CEM)
Was Sie tun können
- 1Read the fault codes in the central electronic module (CEM) first, since the pedal signal passes through CEM
- 2With a diagnostic tool, read both pedal signals in live data while the pedal is pressed and released; they should follow each other
- 3Check that the fuses are intact; their locations are in the owner's manual or on the fuse box cover
- 4Check the connectors at the pedal sensor and the engine control module for contact resistance and oxidation
- 5Use a multimeter to check the supply and ground wires to the pedal sensor for open circuit
- 6If the checks reveal nothing and the fault persists, the pedal sensor can be swapped
Symptome, die Sie bemerken können2
- Yellow warning symbol and a message in the display
- The car has poor performance and lacks power
Was der Fehler beeinflussen kann1
- Engine torque and output may be limited
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.