VOLVO
ECM-P230712 - Ignition Coil C Primary Control Circuit High. General Electrical Failures. Circuit short to battery
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
7 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Modelle nach Baujahr und Motor anzeigen (20)
- Volvo S60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Nur Motor: B4204T6
- Volvo S80 (2007–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Nur Motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Nur Motor: B4164T
- Volvo V40 (2013–)2013Nur Motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Nur Motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B4164T
- Volvo V60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Nur Motor: B4204T6
- Volvo V70 (2008–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Nur Motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Nur Motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Nur Motor: B4204T6
- Volvo XC60 (2009–)2011–2012Nur Motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Nur Motor: B4204T7
Was bedeutet der Fehlercode?
The engine control module (ECM) monitors the signal line to the ignition coil primary winding. The code is set when the signal is too high, which here means the signal line to ignition coil 3 has been short-circuited to supply voltage. It is an electrical fault in the circuit, and the code applies only to ignition coil 3.
Mögliche Ursachen
- The signal wire to ignition coil 3 is short-circuited to supply voltage
- The ignition coil is damaged
Was Sie tun können
- 1The fuses for engine management should be intact; their locations are shown in the car's owner's manual
- 2Read and note the code, clear it, then drive for a while to see whether it returns
- 3Inspect the connector and cable at ignition coil 3 for loose contacts, corrosion and chafing
- 4Use a multimeter to check that the wire to ignition coil 3 has no contact with supply voltage
- 5If the fault returns, have a workshop with diagnostic equipment check the ignition coil and the wiring
Symptome, die Sie bemerken können2
- The engine warning lamp (Check engine) lights up or behaves abnormally
- The car runs poorly and lacks power
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.