VOLVO
ECM-P250A13 - Engine Oil Level Sensor Circuit. General Electrical Failures. Circuit open
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
8 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–), XC70 (2008–)
Modelle nach Baujahr und Motor anzeigen (17)
- Volvo S60 (2011–)2011–2012Nur Motor: B5254T5
- Volvo S60 (2011–)2014–2015Nur Motor: B4204T10, B4204T11, B4204T12, B4204T15, B4204T9, D4204T5
- Volvo S80 (2007–)2007–2008Nur Motor: B5254T6
- Volvo S80 (2007–)2009Nur Motor: B5254T6, B5254T8
- Volvo S80 (2007–)2010–2011Nur Motor: B5254T10, B5254T11, B5254T8
- Volvo S80 (2007–)2012Nur Motor: B5254T10
- Volvo S80 (2007–)2014–2015Nur Motor: B4204T11, B4204T12, B4204T15, D4204T5
- Volvo V40 (2013–)2015Nur Motor: B4204T11, D4204T14
- Volvo V40 Cross Country (2013–)2015Nur Motor: B4204T11, D4204T14
- Volvo V60 (2011–)2014–2015Nur Motor: B4204T11, B4204T12, B4204T15, B4204T9, D4204T5
- Volvo V70 (2008–)2008Nur Motor: B5254T6
- Volvo V70 (2008–)2009Nur Motor: B5254T6, B5254T8
- Volvo V70 (2008–)2010–2011Nur Motor: B5254T10, B5254T11
- Volvo V70 (2008–)2012Nur Motor: B5254T10
- Volvo V70 (2008–)2014–2015Nur Motor: B4204T11, D4204T5
- Volvo XC60 (2009–)2014–2015Nur Motor: B4204T10, B4204T11, B4204T12, B4204T15, B4204T9, D4204T5
- Volvo XC70 (2008–)2014–2015Nur Motor: B4204T11, D4204T5
Was bedeutet der Fehlercode?
The ECM reads the signal from the oil level sensor and uses it to monitor the oil level. The code is stored when that signal is incorrect, which may be an electrical fault in the sensor or its wiring. Water or fuel in the engine oil can also trigger it.
Mögliche Ursachen
- Contact resistance, oxidation or loose contact in the connections
- Open circuit in the signal wire
- Open circuit in the power supply
- Water or fuel in the engine oil
- Damaged oil level sensor
Was Sie tun können
- 1Read the fault status with the engine running. If the code is not active, the fault may have been intermittent
- 2Check that the relevant fuses are intact
- 3Check whether water or fuel may have got into the engine oil. If so, the code can be set, and the remedy is to run the engine fully warm
- 4Use a multimeter to check that the power supply and signal wire to the oil level sensor have no open circuit
- 5If the fault remains after these checks, have a workshop with diagnostic equipment check the oil level sensor
Symptome, die Sie bemerken können1
- The oil pressure warning lamp comes on or behaves abnormally
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.