VOLVO
ECM-U011186 - Lost Communication With Battery Energy Control Module "A". Bus Signal / Message Failures. Signal invalid
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
7 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Modelle nach Baujahr und Motor anzeigen (20)
- Volvo S60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Nur Motor: B4204T6
- Volvo S80 (2007–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Nur Motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Nur Motor: B4164T
- Volvo V40 (2013–)2013Nur Motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Nur Motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B4164T
- Volvo V60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Nur Motor: B4204T6
- Volvo V70 (2008–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Nur Motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Nur Motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Nur Motor: B4204T6
- Volvo XC60 (2009–)2011–2012Nur Motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Nur Motor: B4204T7
Was bedeutet der Fehlercode?
The engine control module (ECM) constantly receives data over the CAN network from the central electronics control module (CEM). The code is set when the engine control module registers a signal from the central electronics control module that it judges to be invalid. Although the code is titled lost communication with the battery energy control module “A”, it applies to the CAN communication with the central electronics control module.
Mögliche Ursachen
- The central electronics control module (CEM) sends faulty or invalid signals
- Intermittent breaks in one or both CAN wires
- Intermittent short circuits between the CAN wires, or to ground or supply voltage
- Incorrect signal configuration in a control module that was replaced without new software being loaded
- A fault in another control module on the same part of the CAN network that sends faulty messages
Was Sie tun können
- 1Read the codes in the engine control module and first fix any other CAN-related codes, as they may share the same cause
- 2Clear the code and road test the car to see if it is set again
- 3Check the CAN wiring between the engine control module and the central electronics control module for chafing, pinched areas and loose connectors
- 4Use a multimeter to check that the CAN wires have no break and are not shorted to ground or supply voltage
- 5Check that the battery has good voltage and that the fuses are intact
- 6If the fault returns: have a workshop with diagnostic equipment check the central electronics control module and the CAN communication. Do not work on the battery system yourself
Symptome, die Sie bemerken können1
- No noticeable symptoms for the driver
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.