VOLVO
ECM-U030000 - Internal Control Module Software Incompatibility. General Failure Information. No sub type information
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
14 ModelleC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Modelle nach Baujahr und Motor anzeigen (17)
- Volvo C30 (2007–2013)2011–2013Nur Motor: D4162T, D5204T, D5204T5
- Volvo C70 (2006–2013)2011Nur Motor: D5204T, D5204T5
- Volvo C70 (2006–2013)2012–2013Alle Motoren außer: B5254T7
- Volvo S40 (2004–2013)2011–2012Nur Motor: D4162T, D5204T, D5204T5
- Volvo S60 (2011–)2011–2015
- Volvo S80 (2007–)2007–2015
- Volvo V40 (2013–)2013–2015
- Volvo V40 Cross Country (2013–)2013–2015
- Volvo V50 (2004–2013)2011–2012Nur Motor: D4162T, D5204T, D5204T5
- Volvo V60 (2011–)2011–2015
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008–2015
- Volvo XC60 (2009–)2009–2015
- Volvo XC70 (2008–)2008–2015
- Volvo XC90 (2003–)2007–2010Nur Motor: B6324S
- Volvo XC90 (2003–)2011–2012Nur Motor: B6324S5
- Volvo XC90 (2003–)2013–2014Alle Motoren außer: B5254T9
Was bedeutet der Fehlercode?
The engine control module (ECM) compares its own configuration ID with the ID that the central electronics control module (CEM) sends out on the CAN network. The code is set when the IDs do not match, and also when communication with the CEM is or has been interrupted. Although the code is titled internal software incompatibility, it concerns a configuration ID that does not match the CEM.
Mögliche Ursachen
- Wrong configuration ID because the module is not intended for the car, for example a used module with different software or hardware
- Break in the CAN wires between the engine control module and the CEM
- Intermittent breaks on one or both CAN wires
Was Sie tun können
- 1Read the codes in the central electronics control module and other control modules, and fix communication faults first
- 2Check that the fuses are intact
- 3Check the CAN connectors for contact resistance and oxidation
- 4Look for chafed CAN wires. Use a multimeter to check that they have no break or short to ground or supply voltage
- 5If the module was recently replaced: have a workshop check that it is intended for this car and has the correct software and configuration
Symptome, die Sie bemerken können5
- The cruise control does not work at all
- The engine jerks on throttle and sharply after engine braking
- Uneven idle
- The engine does not start
- The general warning lamp is on
Was der Fehler beeinflussen kann2
- The module shuts off from the CAN network (bus-off) and stops sending messages
- The module's functions stop working
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.