VOLVO
ECM-U200583 - Vehicle Speed. Bus Signal / Message Failures. Value of signal protection calculation incorrect
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
7 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Modelle nach Baujahr und Motor anzeigen (20)
- Volvo S60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Nur Motor: B4204T6
- Volvo S80 (2007–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Nur Motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Nur Motor: B4164T
- Volvo V40 (2013–)2013Nur Motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Nur Motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B4164T
- Volvo V60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Nur Motor: B4204T6
- Volvo V70 (2008–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Nur Motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Nur Motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Nur Motor: B4204T6
- Volvo XC60 (2009–)2011–2012Nur Motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Nur Motor: B4204T7
Was bedeutet der Fehlercode?
The engine control module (ECM) checks the messages from the brake control module (BCM). The code is set when the ECM finds that a message from the BCM has an incorrect checksum, which means the message is faulty. Interference on the CAN network or a damaged BCM may lie behind it.
Mögliche Ursachen
- Interference in the CAN network
- Damaged brake control module (BCM)
Was Sie tun können
- 1Read the fault codes in the engine control module. If any of ECM-U012088, ECM-U000188, ECM-U1A1400, ECM-U000108 or ECM-U000100 is stored, investigate it first.
- 2Read the fault codes in the brake control module (BCM) and remedy any faults there first.
- 3Look for loose or chafed wires and connectors in the CAN network between the BCM and the engine control module, since network interference can cause this code.
- 4Do not work on the brake system yourself. Have a workshop check the BCM if the code returns.
Symptome, die Sie bemerken können1
- The check engine lamp lights up or behaves abnormally
Was der Fehler beeinflussen kann1
- The BCM's speed signal is replaced by a substitute value
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.