VOLVO
ECM-U201255 - Car Configuration Parameter(s). System Programming Failures. Not configured
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
7 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Modelle nach Baujahr und Motor anzeigen (20)
- Volvo S60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Nur Motor: B4204T6
- Volvo S80 (2007–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Nur Motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Nur Motor: B4164T
- Volvo V40 (2013–)2013Nur Motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Nur Motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B4164T
- Volvo V60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Nur Motor: B4204T6
- Volvo V70 (2008–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Nur Motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Nur Motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Nur Motor: B4204T6
- Volvo XC60 (2009–)2011–2012Nur Motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Nur Motor: B4204T7
Was bedeutet der Fehlercode?
The engine control module (ECM) is meant to receive information about the vehicle configuration from the central electronic module (CEM) over CAN. The code is set when that signal is missing or incorrect. The fault may lie in the CEM or in the communication on the CAN network.
Mögliche Ursachen
- Fault in the central electronic module (CEM)
- Faulty CAN communication
Was Sie tun können
- 1Read the fault codes in the CEM and remedy any faults there first.
- 2Check that the connectors on the CAN network are secure and clean, and look for chafed wiring. Gently wiggle wires and connectors to see whether the fault appears.
- 3Have a workshop with diagnostic equipment measure the resistance in the CAN network, as this requires measurement.
- 4Do not replace the CEM for a CAN fault unless troubleshooting shows an internal fault. Erase the codes in all modules, start the car and check that the code does not return.
Symptome, die Sie bemerken können1
- No noticeable symptoms for the driver
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.