VOLVO
ECM-U210000 - Initial Configuration Not Complete. General Failure Information. No sub type information
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Dieser Fehlercode hat je nach Modell, Modelljahr oder Motor unterschiedliche Bedeutungen. Wählen Sie die Bedeutung, die für Ihr Fahrzeug gilt.
Gilt für folgende Modelle:
10 ModelleC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V70 (2008–)
Modelle nach Baujahr und Motor anzeigen (15)
- Volvo C30 (2007–2013)2011–2013Nur Motor: D4162T, D5204T, D5204T5
- Volvo C70 (2006–2013)2011Nur Motor: D5204T, D5204T5
- Volvo C70 (2006–2013)2012–2013Alle Motoren außer: B5254T7
- Volvo S40 (2004–2013)2011–2012Nur Motor: D4162T, D5204T, D5204T5
- Volvo S60 (2011–)2011–2015Nur Motor: D4162T
- Volvo S80 (2007–)2008–2010Nur Motor: D4204T
- Volvo S80 (2007–)2012–2015Nur Motor: D4162T
- Volvo V40 (2013–)2013–2015Nur Motor: D4162T
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: D4162T
- Volvo V50 (2004–2013)2011–2012Nur Motor: D4162T, D5204T, D5204T5
- Volvo V60 (2011–)2011–2012Nur Motor: D4162T
- Volvo V60 (2011–)2013–2014Nur Motor: D4162T, D82PHEV
- Volvo V60 (2011–)2015Nur Motor: D4162T, D82PHEV, D87PHEV
- Volvo V70 (2008–)2008–2010Nur Motor: D4204T
- Volvo V70 (2008–)2012–2015Nur Motor: D4162T
Was bedeutet der Fehlercode?
The engine control module (ECM) receives information about the vehicle configuration from the central electronic module (CEM). The code is set when that information is incorrect or missing. If the code was set only once and no faults are found after several drive cycles, it most likely came from a software update.
Mögliche Ursachen
- Fault in the central electronic module (CEM)
- The code can be set during a software update
- Open circuit in the CAN network
- Communication cable short-circuited to ground
- Communication cable short-circuited to supply voltage
- Contact resistance, oxidation or poor contact in the connections
Was Sie tun können
- 1Read the fault codes in the central electronic module (CEM) and remedy them first. This code can be erased only once the CEM fault is remedied and erased.
- 2If the code was set once after a software update and does not return, erase it without further action.
- 3Check that the connectors to the CAN network are secure and clean, and look for loose or chafed wiring.
- 4If the code returns, have a workshop read the fault counter and troubleshoot the CAN network with diagnostic equipment.
Symptome, die Sie bemerken können2
- Warning symbol and message in the display
- Cruise control cannot be engaged
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.