VOLVO
ECM-U210787 - Collision Mitigation By Braking. Bus Signal / Message Failures. Missing message
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
9 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–)
Modelle nach Baujahr und Motor anzeigen (24)
- Volvo S60 (2011–)2011–2012Nur Motor: B6304T4
- Volvo S60 (2011–)2013–2014Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14, B6304T4
- Volvo S60 (2011–)2015Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14, B6304T3, B6304T4, B6304T5
- Volvo S80 (2007–)2010Nur Motor: B6304T2, B6324S, B6324S2, B8444S
- Volvo S80 (2007–)2011Nur Motor: B6304T4, B6324S4, B6324S5, B8444S
- Volvo S80 (2007–)2012, 2015Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo S80 (2007–)2013–2014Nur Motor: B5254T12, B5254T14, B6304T4, B6324S4, B6324S5
- Volvo V40 (2013–)2013–2014Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V40 (2013–)2015Nur Motor: B5204T8, B5204T9
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V60 (2011–)2011–2012Nur Motor: B6304T4
- Volvo V60 (2011–)2013Nur Motor: B5204T8, B5204T9, B6304T4
- Volvo V60 (2011–)2014Nur Motor: B5204T8, B5204T9, B5254T12, B6304T4
- Volvo V60 (2011–)2015Nur Motor: B5204T9, B5254T12, B6304T3, B6304T4, B6304T5
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2010Nur Motor: B6304T2, B6324S, B6324S2
- Volvo V70 (2008–)2011–2012Nur Motor: B6304T4, B6324S5
- Volvo V70 (2008–)2013–2014Nur Motor: B5204T9, B6304T4, B6324S5
- Volvo V70 (2008–)2015Nur Motor: B5204T9, B6304T4
- Volvo XC60 (2009–)2010Nur Motor: B6304T2, B6324S, B6324S2
- Volvo XC60 (2009–)2011–2014Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo XC60 (2009–)2015Nur Motor: B5204T9, B5254T12, B5254T14, B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2010Nur Motor: B6304T2, B6324S, B6324S2
- Volvo XC70 (2008–)2011–2015Nur Motor: B6304T4, B6324S4, B6324S5
Was bedeutet der Fehlercode?
The engine control module (ECM) gets signals from the forward sensing module (FSM) and the central electronic module (CEM) and applies braking help when a collision threatens. The code is set when one of the input signals from the FSM or the CEM is lost, which means an expected message is missing. The fault may lie in the FSM or the CEM, or in the communication between them and the engine control module.
Mögliche Ursachen
- The fault is in the forward sensing module (FSM)
- Open circuit in the communication cable
- Communication cable short-circuited to ground or to voltage
- Contact resistance or oxidation in the connections
- Open circuit or short-circuit in the connections
- The fault is in the central electronic module (CEM)
Was Sie tun können
- 1Read the fault codes in the engine control module. If any of ECM-U012088, ECM-U000188, ECM-U1A1400, ECM-U000108 or ECM-U000100 is stored, check it first.
- 2Read the fault codes in the FSM and the CEM and remedy any faults there first. The engine control module code is then a follow-on fault.
- 3Check that the connectors in the CAN network are secure and clean, and look for chafed wiring.
- 4Do not replace the CEM for a CAN fault unless a workshop has confirmed an internal fault in it.
Symptome, die Sie bemerken können2
- Warning symbol and message in the display
- Message in the display
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.