VOLVO
SAS-U300362 - Battery Voltage. Algorithm Based Failures. Signal compare failure
System
Lenkwinkelsensor (SAS)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
14 ModelleC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Modelle nach Baujahr und Motor anzeigen (19)
- Volvo C30 (2007–2013)2011–2013Nur Motor: D4162T, D5204T, D5204T5
- Volvo C70 (2006–2013)2011Nur Motor: D5204T, D5204T5
- Volvo C70 (2006–2013)2012–2013Alle Motoren außer: B5254T7
- Volvo S40 (2004–2013)2011–2012Nur Motor: D4162T, D5204T, D5204T5
- Volvo S60 (2011–)2011–2015
- Volvo S80 (2007–)2007–2015
- Volvo V40 (2013–)2013–2015
- Volvo V40 Cross Country (2013–)2013–2015
- Volvo V50 (2004–2013)2011–2012Nur Motor: D4162T, D5204T, D5204T5
- Volvo V60 (2011–)2011–2015
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008–2015
- Volvo XC60 (2009–)2009–2015
- Volvo XC70 (2008–)2008–2015
- Volvo XC90 (2003–)2005–2006Nur Motor: B8444S
- Volvo XC90 (2003–)2007–2010Nur Motor: B6324S, B8444S
- Volvo XC90 (2003–)2011Nur Motor: B6324S5, B8444S
- Volvo XC90 (2003–)2012Nur Motor: B6324S5
- Volvo XC90 (2003–)2013–2014Alle Motoren außer: B5254T9
Was bedeutet der Fehlercode?
Although the code is named battery voltage, it applies when the steering angle sensor compares its voltage with that of the central electronic module (CEM) and the two do not agree. The cause can be poor contact or oxidation at the connector on the steering wheel module, or an internal fault in the sensor.
Mögliche Ursachen
- Poor contact or oxidised connector on the steering wheel module (SWM).
- Internal malfunction within the sensor (SAS).
Was Sie tun können
- 1Clear the code and test drive the car. It mainly needs action if it has been active a long time and a function is lost.
- 2With a diagnostic tool and the ignition on, compare the voltage values of the steering angle sensor and the CEM. They should be roughly the same.
- 3Check that the fuses are intact and that the connectors to the steering wheel module are firmly seated and not corroded.
- 4Have a workshop replace the contact reel or angle sensor if the fault returns. If the code comes back after that, the steering wheel module (SWM) must be replaced.
- 5The angle sensor is part of the steering and stability system. Have a workshop carry out the checks and repair rather than working on the steering wheel yourself.
Symptome, die Sie bemerken können5
- The information lamp lights up
- The anti-spin warning lamp lights up
- Traction control and the stability function do not work
- The Four-C function does not work
- A yellow warning symbol and text message show in the display
Was der Fehler beeinflussen kann2
- The stability function is blocked
- The sensor warns the other control modules that the data it sends is wrong
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.