VOLVO
TCM-P072268 - Output Shaft Speed Sensor Circuit No Signal. Algorithm Based Failures. Event information
System
Getriebesteuergerät (TCM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
7 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Modelle nach Baujahr und Motor anzeigen (16)
- Volvo S60 (2011–)2012Nur Motor: D5204T3 · Nur Getriebe: TF-80SD
- Volvo S60 (2011–)2013–2014Nur Motor: B5204T8, B5204T9, D5204T3, D5204T7 · Nur Getriebe: TF-80SD
- Volvo S60 (2011–)2015Nur Motor: D5204T3, D5204T7 · Nur Getriebe: TF-80SD
- Volvo S80 (2007–)2012, 2015Nur Motor: D5204T3 · Nur Getriebe: TF-80SD
- Volvo S80 (2007–)2013–2014Nur Motor: D5204T3, D5204T7 · Nur Getriebe: TF-80SD
- Volvo V40 (2013–)2013Alle Motoren außer: B4164T, B4164T3, D4162T · Nur Getriebe: TF-80SD
- Volvo V40 (2013–)2014Alle Motoren außer: B4164T, B4164T3, B4164T4, D4162T · Nur Getriebe: TF-80SD
- Volvo V40 (2013–)2015Nur Motor: B5204T8, B5204T9, D5204T6 · Nur Getriebe: TF-80SD
- Volvo V40 Cross Country (2013–)2013–2014Alle Motoren außer: B4164T, D4162T · Nur Getriebe: TF-80SD, TF-80SD AWD
- Volvo V40 Cross Country (2013–)2015Alle Motoren außer: B4164T, B4204T11, D4162T, D4204T14 · Nur Getriebe: TF-80SD, TF-80SD AWD
- Volvo V60 (2011–)2012Nur Motor: D5204T3 · Nur Getriebe: TF-80SD
- Volvo V60 (2011–)2013–2014Nur Motor: B5204T8, B5204T9, D5204T3, D5204T7, D82PHEV · Nur Getriebe: TF-80SD
- Volvo V60 (2011–)2015Nur Motor: B5204T9, D5204T3, D5204T7, D82PHEV, D87PHEV · Nur Getriebe: TF-80SD
- Volvo V70 (2008–)2012Nur Motor: D5204T3 · Nur Getriebe: TF-80SD
- Volvo V70 (2008–)2013–2015Nur Motor: D5204T3, D5204T7 · Nur Getriebe: TF-80SD
- Volvo XC60 (2009–)2015Nur Motor: B5204T9 · Nur Getriebe: TF-80SD AWD
Was bedeutet der Fehlercode?
This is an event-driven information code and does not indicate a fault in the control module where it is active. It is always set together with another fault code, and that other code shows the real fault, so deal with that one first.
Mögliche Ursachen
- Higher resistance at a connection
- Output shaft speed sensor not seated correctly
- Output shaft speed sensor not working
- A fault inside the TCM itself
Was Sie tun können
- 1Read all stored codes: this code is always set together with another one, which is the real fault
- 2Deal with the other code first, following its own instructions
- 3Then clear the codes and road test; this code does not need separate work
- 4If the other code returns after the repair, have a workshop check it
Symptome, die Sie bemerken können5
- Lock-up does not work
- No automatic gear change
- Gear changes are harsh or jerky
- The PURE, SAVE and AWD drive modes switch off automatically and cannot be selected
- In HYBRID mode the combustion engine runs all the time or too often
Was der Fehler beeinflussen kann1
- Electric propulsion is not possible
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.