VOLVO
TCM-P100987 - Hybrid Drive Mode. Bus Signal / Message Failures. Missing message
System
Getriebesteuergerät (TCM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
7 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Modelle nach Baujahr und Motor anzeigen (16)
- Volvo S60 (2011–)2012Nur Motor: D5204T3 · Nur Getriebe: TF-80SD
- Volvo S60 (2011–)2013–2014Nur Motor: B5204T8, B5204T9, D5204T3, D5204T7 · Nur Getriebe: TF-80SD
- Volvo S60 (2011–)2015Nur Motor: D5204T3, D5204T7 · Nur Getriebe: TF-80SD
- Volvo S80 (2007–)2012, 2015Nur Motor: D5204T3 · Nur Getriebe: TF-80SD
- Volvo S80 (2007–)2013–2014Nur Motor: D5204T3, D5204T7 · Nur Getriebe: TF-80SD
- Volvo V40 (2013–)2013Alle Motoren außer: B4164T, B4164T3, D4162T · Nur Getriebe: TF-80SD
- Volvo V40 (2013–)2014Alle Motoren außer: B4164T, B4164T3, B4164T4, D4162T · Nur Getriebe: TF-80SD
- Volvo V40 (2013–)2015Nur Motor: B5204T8, B5204T9, D5204T6 · Nur Getriebe: TF-80SD
- Volvo V40 Cross Country (2013–)2013–2014Alle Motoren außer: B4164T, D4162T · Nur Getriebe: TF-80SD, TF-80SD AWD
- Volvo V40 Cross Country (2013–)2015Alle Motoren außer: B4164T, B4204T11, D4162T, D4204T14 · Nur Getriebe: TF-80SD, TF-80SD AWD
- Volvo V60 (2011–)2012Nur Motor: D5204T3 · Nur Getriebe: TF-80SD
- Volvo V60 (2011–)2013–2014Nur Motor: B5204T8, B5204T9, D5204T3, D5204T7, D82PHEV · Nur Getriebe: TF-80SD
- Volvo V60 (2011–)2015Nur Motor: B5204T9, D5204T3, D5204T7, D82PHEV, D87PHEV · Nur Getriebe: TF-80SD
- Volvo V70 (2008–)2012Nur Motor: D5204T3 · Nur Getriebe: TF-80SD
- Volvo V70 (2008–)2013–2015Nur Motor: D5204T3, D5204T7 · Nur Getriebe: TF-80SD
- Volvo XC60 (2009–)2015Nur Motor: B5204T9 · Nur Getriebe: TF-80SD AWD
Was bedeutet der Fehlercode?
The transmission control module (TCM) receives the vehicle's drive mode signal from the engine control module (ECM) via the CAN bus. The fault code is set when the signal from the engine control module is missing or indicated as faulty. The fault is general and does not say more precisely what type of fault it is.
Mögliche Ursachen
- Contact resistance or oxidation at the terminals and joints
- Open circuit in one of the CAN wires
- Short-circuit between the CAN wires
- Fault in the engine control module (ECM)
Was Sie tun können
- 1Read and note the fault codes in the engine control module (ECM) as well, as this code may be caused by a fault there
- 2Have a workshop check the connectors and CAN wiring for oxidation, loose connections, open circuits and short-circuits between the wires
- 3If no fault is found in the wiring, have a workshop locate the cause in the engine control module (ECM)
Symptome, die Sie bemerken können1
- No noticeable symptoms for the driver
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.