VOLVO
TCM-P279601 - Auxiliary Transmission Fluid Pump Control Circuit. General Failure Information. General electrical failure
System
Getriebesteuergerät (TCM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
7 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Modelle nach Baujahr und Motor anzeigen (16)
- Volvo S60 (2011–)2012Nur Motor: D5204T3 · Nur Getriebe: TF-80SD
- Volvo S60 (2011–)2013–2014Nur Motor: B5204T8, B5204T9, D5204T3, D5204T7 · Nur Getriebe: TF-80SD
- Volvo S60 (2011–)2015Nur Motor: D5204T3, D5204T7 · Nur Getriebe: TF-80SD
- Volvo S80 (2007–)2012, 2015Nur Motor: D5204T3 · Nur Getriebe: TF-80SD
- Volvo S80 (2007–)2013–2014Nur Motor: D5204T3, D5204T7 · Nur Getriebe: TF-80SD
- Volvo V40 (2013–)2013Alle Motoren außer: B4164T, B4164T3, D4162T · Nur Getriebe: TF-80SD
- Volvo V40 (2013–)2014Alle Motoren außer: B4164T, B4164T3, B4164T4, D4162T · Nur Getriebe: TF-80SD
- Volvo V40 (2013–)2015Nur Motor: B5204T8, B5204T9, D5204T6 · Nur Getriebe: TF-80SD
- Volvo V40 Cross Country (2013–)2013–2014Alle Motoren außer: B4164T, D4162T · Nur Getriebe: TF-80SD, TF-80SD AWD
- Volvo V40 Cross Country (2013–)2015Alle Motoren außer: B4164T, B4204T11, D4162T, D4204T14 · Nur Getriebe: TF-80SD, TF-80SD AWD
- Volvo V60 (2011–)2012Nur Motor: D5204T3 · Nur Getriebe: TF-80SD
- Volvo V60 (2011–)2013–2014Nur Motor: B5204T8, B5204T9, D5204T3, D5204T7, D82PHEV · Nur Getriebe: TF-80SD
- Volvo V60 (2011–)2015Nur Motor: B5204T9, D5204T3, D5204T7, D82PHEV, D87PHEV · Nur Getriebe: TF-80SD
- Volvo V70 (2008–)2012Nur Motor: D5204T3 · Nur Getriebe: TF-80SD
- Volvo V70 (2008–)2013–2015Nur Motor: D5204T3, D5204T7 · Nur Getriebe: TF-80SD
- Volvo XC60 (2009–)2015Nur Motor: B5204T9 · Nur Getriebe: TF-80SD AWD
Was bedeutet der Fehlercode?
The transmission control module (TCM) has detected an electrical fault in the circuit to the auxiliary electric transmission oil pump. The pump is meant to ensure the transmission gets the right pressure and flow while the automatic start/stop function is active, so that pressure does not drop. The fault means the car cannot be driven on electric propulsion.
Mögliche Ursachen
- Contact resistance, oxidation or poor connection in connectors or joints
- Open circuit or short to ground in the wiring
- Short to supply voltage in the wiring
- Internal fault in the electric oil pump
Was Sie tun können
- 1Read and note the code, clear it and road test the car to see whether it returns
- 2Check the battery condition and that the fuses are intact
- 3If the fault returns, have a workshop check the connectors and signal wires to the oil pump, and replace the electric oil pump if needed
Symptome, die Sie bemerken können2
- The drive modes PURE, SAVE and AWD switch off automatically and are not available
- In HYBRID mode the combustion engine is active all the time or too often
Was der Fehler beeinflussen kann1
- Electric propulsion is not possible
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.