VOLVO
BCM-C000301 - TCS Control Channel "B" Valve 1. General Failure Information. General electrical failure
Układ
Sterownik układu hamulcowego (BCM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
13 modeliC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–)
Pokaż modele wg rocznika i silnika (16)
- Volvo C30 (2007–2013)2011–2013Tylko silnik: D4162T, D5204T, D5204T5
- Volvo C70 (2006–2013)2011Tylko silnik: D5204T, D5204T5
- Volvo C70 (2006–2013)2012–2013Wszystkie silniki oprócz: B5254T7
- Volvo S40 (2004–2013)2011–2012Tylko silnik: D4162T, D5204T, D5204T5
- Volvo S60 (2011–)2011–2015
- Volvo S80 (2007–)2007–2015
- Volvo V40 (2013–)2013–2015
- Volvo V40 Cross Country (2013–)2013–2015
- Volvo V50 (2004–2013)2011–2012Tylko silnik: D4162T, D5204T, D5204T5
- Volvo V60 (2011–)2011–2012
- Volvo V60 (2011–)2013–2014Wszystkie silniki oprócz: D82PHEV
- Volvo V60 (2011–)2015Wszystkie silniki oprócz: D82PHEV, D87PHEV
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008–2015
- Volvo XC60 (2009–)2009–2015
- Volvo XC70 (2008–)2008–2015
Co oznacza ten kod błędu?
The brake control module has twelve valve coils for the valves in the hydraulic unit and has registered an electrical fault in the coil for control channel B, valve 1. The fault may be a value that is too low or too high in the signal. The valves control brake pressure for ABS, stability and traction control, and the fault is often due to an internal disturbance in the module.
Możliwe przyczyny
- Fault inside the brake control module (BCM)
Co możesz zrobić
- 1Activate the hydraulic unit valves with diagnostic equipment; if no ticking sound is heard from the valves, the module has an internal fault
- 2Clear the code and road test; if it returns, a workshop should replace the brake control module
- 3After replacement, programming and calibration are needed, as a new module is supplied without software
- 4The brake system is safety critical: do not work on the brake control module or hydraulic unit yourself, and drive carefully until the fault is fixed
Objawy, które możesz zauważyć5
- General warning lamp on
- The brake circuit does not work and the warning lamp comes on
- Anti-spin, stability and anti-skid do not work
- Traction control does not work
- Information lamp on
Na co może wpływać usterka3
- ABS is disabled
- Traction control, stability control and active yaw control (AYC) are disabled
- Electronic brake force distribution (EBD) and brake assist are disabled
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.