VOLVO
BCM-C002001 - ABS Pump Motor Control. General Failure Information. General electrical failure
Układ
Sterownik układu hamulcowego (BCM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
14 modeliC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Pokaż modele wg rocznika i silnika (21)
- Volvo C30 (2007–2013)2011–2013Tylko silnik: D4162T, D5204T, D5204T5
- Volvo C70 (2006–2013)2011Tylko silnik: D5204T, D5204T5
- Volvo C70 (2006–2013)2012–2013Wszystkie silniki oprócz: B5254T7
- Volvo S40 (2004–2013)2011–2012Tylko silnik: D4162T, D5204T, D5204T5
- Volvo S60 (2011–)2011–2015
- Volvo S80 (2007–)2007–2015
- Volvo V40 (2013–)2013–2015
- Volvo V40 Cross Country (2013–)2013–2015
- Volvo V50 (2004–2013)2011–2012Tylko silnik: D4162T, D5204T, D5204T5
- Volvo V60 (2011–)2011–2012
- Volvo V60 (2011–)2013–2014Wszystkie silniki oprócz: D82PHEV
- Volvo V60 (2011–)2015Wszystkie silniki oprócz: D82PHEV, D87PHEV
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008–2015
- Volvo XC60 (2009–)2009–2015
- Volvo XC70 (2008–)2008–2015
- Volvo XC90 (2003–)2005–2006Tylko silnik: B8444S
- Volvo XC90 (2003–)2007–2010Tylko silnik: B6324S, B8444S
- Volvo XC90 (2003–)2011Tylko silnik: B6324S5, B8444S
- Volvo XC90 (2003–)2012Tylko silnik: B6324S5
- Volvo XC90 (2003–)2013–2014Wszystkie silniki oprócz: B5254T9
Co oznacza ten kod błędu?
The brake control module (BCM) has detected that the ABS pump motor does not start or that its signal is missing. The pump motor sits in the hydraulic unit and builds the brake pressure needed for ABS, stability control and brake assistance.
Możliwe przyczyny
- Poor contact or oxidation in the connections to the pump motor and the brake control module
- Blown fuse for the pump motor
- Open circuit in the supply or ground wire to the pump motor
- Damaged pump motor
- Faulty brake control module (uncommon)
Co możesz zrobić
- 1Read the code, clear it and road test the car to see whether it returns
- 2Check the pump motor fuse. If it has blown, check the circuit for a short to ground before fitting a new fuse
- 3Check that the connectors at the brake control module and the pump motor are secure and free from oxidation
- 4With diagnostic equipment activate the pump motor and check that it starts and runs normally. If it does, the fault may have been temporary
- 5If the pump motor does not start, the hydraulic unit normally needs replacing by a workshop
- 6Do not work on the brake hydraulic unit or pump motor yourself; leave this to a workshop. Drive carefully until the fault is fixed
Objawy, które możesz zauważyć5
- General warning lamp and ABS warning lamp on
- ABS, traction control and stability function do not work
- Anti-skid function does not work
- Adaptive cruise control, collision warning and auto brake do not work
- Electronic parking brake has reduced function
Na co może wpływać usterka2
- ABS, traction control, stability control and brake assistance are blocked
- The brakes still work but without ABS regulation
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.