VOLVO
BCM-C00201C - ABS Pump Motor Control. General Electrical Failures. Circuit voltage out of range
Układ
Sterownik układu hamulcowego (BCM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
14 modeliC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Pokaż modele wg rocznika i silnika (21)
- Volvo C30 (2007–2013)2011–2013Tylko silnik: D4162T, D5204T, D5204T5
- Volvo C70 (2006–2013)2011Tylko silnik: D5204T, D5204T5
- Volvo C70 (2006–2013)2012–2013Wszystkie silniki oprócz: B5254T7
- Volvo S40 (2004–2013)2011–2012Tylko silnik: D4162T, D5204T, D5204T5
- Volvo S60 (2011–)2011–2015
- Volvo S80 (2007–)2007–2015
- Volvo V40 (2013–)2013–2015
- Volvo V40 Cross Country (2013–)2013–2015
- Volvo V50 (2004–2013)2011–2012Tylko silnik: D4162T, D5204T, D5204T5
- Volvo V60 (2011–)2011–2012
- Volvo V60 (2011–)2013–2014Wszystkie silniki oprócz: D82PHEV
- Volvo V60 (2011–)2015Wszystkie silniki oprócz: D82PHEV, D87PHEV
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008–2015
- Volvo XC60 (2009–)2009–2015
- Volvo XC70 (2008–)2008–2015
- Volvo XC90 (2003–)2005–2006Tylko silnik: B8444S
- Volvo XC90 (2003–)2007–2010Tylko silnik: B6324S, B8444S
- Volvo XC90 (2003–)2011Tylko silnik: B6324S5, B8444S
- Volvo XC90 (2003–)2012Tylko silnik: B6324S5
- Volvo XC90 (2003–)2013–2014Wszystkie silniki oprócz: B5254T9
Co oznacza ten kod błędu?
The brake control module (BCM) has detected that the voltage supplied to the ABS pump motor is incorrect. The pump motor sits in the hydraulic unit and builds the brake pressure needed for ABS, stability control and brake assistance. The check only runs once the car has been moving, so the fault is usually noticed while driving.
Możliwe przyczyny
- Poor contact or oxidation in the connections to the pump motor and the brake control module
- Blown fuse for the pump motor
- Open circuit in the supply or ground wire to the pump motor
- Damaged pump motor
- Faulty brake control module (uncommon)
Co możesz zrobić
- 1Read the code, clear it and road test the car to see whether it comes back
- 2Check the pump motor fuse in the engine bay fuse box; if it has blown, check the circuit for a short to ground before a new fuse is fitted
- 3Check the connectors at the brake control module and the pump motor for poor contact and oxidation
- 4With diagnostic equipment run the pump motor and check that it starts and runs normally
- 5Do not work on the brake hydraulic unit or pump motor yourself; leave this to a workshop
Objawy, które możesz zauważyć3
- General warning lamp on
- ABS warning lamp on
- ABS, traction control and stability function do not work
Na co może wpływać usterka2
- ABS, traction control, stability control and brake assistance are disabled
- The brakes still work but without ABS regulation
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.