VOLVO
BCM-U000100 - High Speed CAN Communication Bus. General Failure Information. No sub type information
Układ
Sterownik układu hamulcowego (BCM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
12 modeliC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V50 (2004–2013), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Pokaż modele wg rocznika i silnika (17)
- Volvo C30 (2007–2013)2011–2013Tylko silnik: D4162T, D5204T, D5204T5
- Volvo C70 (2006–2013)2011Tylko silnik: D5204T, D5204T5
- Volvo C70 (2006–2013)2012–2013Wszystkie silniki oprócz: B5254T7
- Volvo S40 (2004–2013)2011–2012Tylko silnik: D4162T, D5204T, D5204T5
- Volvo S60 (2011–)2011–2015
- Volvo S80 (2007–)2007–2015
- Volvo V50 (2004–2013)2011–2012Tylko silnik: D4162T, D5204T, D5204T5
- Volvo V60 (2011–)2011–2015
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008–2015
- Volvo XC60 (2009–)2009–2015
- Volvo XC70 (2008–)2008–2015
- Volvo XC90 (2003–)2005–2006Tylko silnik: B8444S
- Volvo XC90 (2003–)2007–2010Tylko silnik: B6324S, B8444S
- Volvo XC90 (2003–)2011Tylko silnik: B6324S5, B8444S
- Volvo XC90 (2003–)2012Tylko silnik: B6324S5
- Volvo XC90 (2003–)2013–2014Wszystkie silniki oprócz: B5254T9
Co oznacza ten kod błędu?
Control modules in the car send and receive information via CAN, a standardised serial communication method. The brake control module (BCM) has detected that the communication on the CAN network is disturbed by another module, or that its own messages are disturbing the network. The fault can only be read out when it is intermittent.
Możliwe przyczyny
- Short circuit between the CAN wires
- Open circuit in one of the CAN wires
- Internal fault in the brake control module
- Internal fault in another module on the same part of the CAN network
Co możesz zrobić
- 1Read codes in the central electronic module; if it shows a loss of power to a module, troubleshoot that module first
- 2Measure the CAN wires against ground, against supply voltage and against each other, looking for shorts and open circuits
- 3Have a workshop disconnect modules on the network one at a time to identify the one causing the disturbance, and replace it if it communicates incorrectly
- 4Clear the codes and check whether the communication fault returns after a road test
- 5The brake system is safety-critical, so have a workshop carry out all work on the network and the modules
Objawy, które możesz zauważyć5
- ABS warning lamp lit and ABS does not work
- Brake circuit does not function and the warning lamp is lit
- Traction control warning lamp lit
- Traction and stability functions do not work
- Adaptive cruise control, collision warning and the electronic parking brake work incompletely
Na co może wpływać usterka2
- The brake control module switches itself off and stays off until the power supply is broken and restored
- Dynamic stability control (AYC) is disabled
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.