VOLVO
BCM-U030000 - Internal Control Module Software Incompatibility. General Failure Information. No sub type information
Układ
Sterownik układu hamulcowego (BCM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
12 modeliC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V50 (2004–2013), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Pokaż modele wg rocznika i silnika (19)
- Volvo C30 (2007–2013)2011–2013Tylko silnik: D4162T, D5204T, D5204T5
- Volvo C70 (2006–2013)2011Tylko silnik: D5204T, D5204T5
- Volvo C70 (2006–2013)2012–2013Wszystkie silniki oprócz: B5254T7
- Volvo S40 (2004–2013)2011–2012Tylko silnik: D4162T, D5204T, D5204T5
- Volvo S60 (2011–)2011–2015
- Volvo S80 (2007–)2007–2015
- Volvo V50 (2004–2013)2011–2012Tylko silnik: D4162T, D5204T, D5204T5
- Volvo V60 (2011–)2011–2012
- Volvo V60 (2011–)2013–2014Wszystkie silniki oprócz: D82PHEV
- Volvo V60 (2011–)2015Wszystkie silniki oprócz: D82PHEV, D87PHEV
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008–2015
- Volvo XC60 (2009–)2009–2015
- Volvo XC70 (2008–)2008–2015
- Volvo XC90 (2003–)2005–2006Tylko silnik: B8444S
- Volvo XC90 (2003–)2007–2010Tylko silnik: B6324S, B8444S
- Volvo XC90 (2003–)2011Tylko silnik: B6324S5, B8444S
- Volvo XC90 (2003–)2012Tylko silnik: B6324S5
- Volvo XC90 (2003–)2013–2014Wszystkie silniki oprócz: B5254T9
Co oznacza ten kod błędu?
The BCM checks its own configuration ID against the one sent by the CEM over the CAN network. If the IDs do not match, or if communication with the CEM has been interrupted, the code is set. The module then responds to diagnostic commands, but normal communication does not work.
Możliwe przyczyny
- Incorrect configuration ID in the brake control module, for example a used module with software or hardware not intended for the car
- Break in the CAN wires between the brake control module and the central electronic module
Co możesz zrobić
- 1Read codes in the central electronic module; if it shows a loss of power supply to a module, troubleshoot that module first
- 2Check that the correct brake control module is fitted for the car, especially if a used module has been installed
- 3Check the CAN wiring between the brake control module and the central electronic module for breaks and contact resistance
- 4Have a workshop program the brake control module with the correct software and check that the code is not set again
- 5The brake system is safety-critical, so have a workshop carry out all work on the module and its software
Objawy, które możesz zauważyć5
- ABS warning lamp lit
- Brake circuit warning lamp lit
- Stability, traction and anti-skid functions do not work
- Adaptive cruise control and collision warning with brake support do not work
- Message in the text display
Na co może wpływać usterka3
- The module switches itself off and responds only to diagnostic commands
- Locking-free brakes, stability control and traction control are disabled
- Dynamic stability control (AYC) is disabled
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.