BCM-U042862 - Invalid Data Received From Steering Angle Sensor Module. Algorithm Based Failures. Signal compare failure
Układ
Sterownik układu hamulcowego (BCM)
Modele Volvo, których dotyczy ten kod błędu
Ten kod błędu ma różne znaczenie w zależności od modelu, rocznika lub silnika. Wybierz znaczenie, które dotyczy Twojego samochodu.
Dotyczy następujących modeli:
13 modeliC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–)
Pokaż modele wg rocznika i silnika (14)
- Volvo C30 (2007–2013)2011–2013Tylko silnik: D4162T, D5204T, D5204T5
- Volvo C70 (2006–2013)2011Tylko silnik: D5204T, D5204T5
- Volvo C70 (2006–2013)2012–2013Wszystkie silniki oprócz: B5254T7
- Volvo S40 (2004–2013)2011–2012Tylko silnik: D4162T, D5204T, D5204T5
- Volvo S60 (2011–)2011–2015
- Volvo S80 (2007–)2007–2015
- Volvo V40 (2013–)2013–2015
- Volvo V40 Cross Country (2013–)2013–2015
- Volvo V50 (2004–2013)2011–2012Tylko silnik: D4162T, D5204T, D5204T5
- Volvo V60 (2011–)2011–2015
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008–2015
- Volvo XC60 (2009–)2009–2015
- Volvo XC70 (2008–)2008–2015
Co oznacza ten kod błędu?
At each new ignition cycle the brake control module (BCM) compares the steering angle from the steering angle sensor with a calculated value. The code is set when the difference between the two values is too large, which most often happens when the steering angle sensor has not been initialised during a longer drive. It applies to cars with a stability system and can be set when stability has been regulated for too long.
Możliwe przyczyny
- The driver has driven for a long time with an uninitialised steering angle sensor after start-up
- The driver drove with an uninitialised steering angle sensor and then switched the ignition off
- Internal fault in the steering angle sensor control module (SAS)
Co możesz zrobić
- 1If other codes are stored in the module, troubleshoot them first
- 2Check the front wheel alignment and have a workshop adjust it if needed
- 3Think back on whether the car has been driven for a long time without the steering wheel being turned after start-up
- 4The brake and stability systems are safety-critical, so have a workshop carry out any work on the steering angle sensor and the brake control module
Objawy, które możesz zauważyć5
- Traction and anti-skid warning lamp lit
- Stability function does not work
- Traction control does not work
- Anti-skid function does not work
- Adaptive cruise control does not work
Na co może wpływać usterka3
- Stability control is disabled
- Traction control is disabled
- Dynamic stability control (AYC) is disabled
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.