Przejdź do treści
    OBD Tuning
    WYŚLIJ DO NAS
    WYŚLIJ DO NAS
    Strona główna
    Kody błędów
    VOLVO
    CEM-8A24
    VOLVO

    CEM-8A24 - Gas discharge lamp module (GDL) left-hand. Faulty signal

    Układ

    Centralny moduł elektroniczny (CEM)

    Modele Volvo, których dotyczy ten kod błędu

    Dotyczy następujących modeli:

    4 modele

    C30 (2007–2013), C70 (2006–2013), S40 (2004–2013), V50 (2004–2013)

    Pokaż modele wg rocznika i silnika (4)
    • Volvo C30 (2007–2013)2007–2011
    • Volvo C70 (2006–2013)2006–2011
    • Volvo S40 (2004–2013)2004–2007
    • Volvo V50 (2004–2013)2004–2007

    Co oznacza ten kod błędu?

    Although the code is named faulty signal, the left-hand gas discharge lamp module (GDL) reports an internal fault to the central electronic module (CEM). The fault may lie in the module, in the lamp housing or in the signal wiring between them. Check the lamp and the wiring before the module is replaced.

    Możliwe przyczyny

    • The left-hand gas discharge lamp module (GDL) is faulty
    • The left-hand lamp housing is faulty
    • Open circuit in the signal wire between the left-hand lamp housing and the gas discharge lamp module
    • The signal wire between the lamp housing and the module is short-circuited to battery voltage
    • The signal wire between the lamp housing and the module is short-circuited to ground

    Co możesz zrobić

    1. 1Switch on the low beam and see whether the left lamp lights. If it does not, check the bulb first and replace it with a new one of the correct type
    2. 2Switch the ignition off and unplug the connectors to the headlamp. Check that they are not oxidised, loose or damaged
    3. 3Use a multimeter to check that the signal wires between the lamp housing and the module are not broken and have no contact with ground or battery voltage
    4. 4After recent removal or replacement, make sure the igniter sits properly. It works on high voltage, so leave other work to a workshop
    5. 5If the fault remains, have a workshop replace the module. After replacement the car data must be programmed in and the position sensors recalibrated

    Objawy, które możesz zauważyć1

    • The low beam does not work

    Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.

    OBD Tuning

    Wiodące centrum ekspertów Szwecji w elektronice motoryzacyjnej. Oferujemy profesjonalną optymalizację silnika, naprawę sterowników i diagnostykę z gwarancją 12 miesięcy.

    Usługi

    • Optymalizacja silnika
    • Naprawa sterownika
    • Klonowanie modułów
    • Zestaw wskaźników
    • SRS / Poduszka powietrzna
    • Immobilizer

    Baza danych & Diagnostyka

    • Baza danych sterowników
    • Katalog kodów DTC
    • Przewodniki diagnostyczne & Pomiary
    • Analizator błędów AI
    • Aktualności

    Producenci ECU

    • Bosch
    • Continental
    • Delphi
    • Delco
    • Denso
    • Magneti Marelli
    • Siemens / VDO
    • Keihin
    • Temic

    Firma

    • O nas
    • Kontakt
    • Partnerzy warsztatów
    • Przewodnik wysyłki
    • Gwarancja
    • FAQ
    • Regulamin
    • Polityka prywatności
    • Mapa strony

    • Optymalizacja silnika
    • Naprawa sterownika
    • Klonowanie modułów
    • Zestaw wskaźników
    • SRS / Poduszka powietrzna
    • Immobilizer

    • Baza danych sterowników
    • Katalog kodów DTC
    • Przewodniki diagnostyczne & Pomiary
    • Analizator błędów AI
    • Aktualności

    • Bosch
    • Continental
    • Delphi
    • Delco
    • Denso
    • Magneti Marelli
    • Siemens / VDO
    • Keihin
    • Temic

    • O nas
    • Kontakt
    • Partnerzy warsztatów
    • Przewodnik wysyłki
    • Gwarancja
    • FAQ
    • Regulamin
    • Polityka prywatności
    • Mapa strony

    Odwiedź nas

    Gjuterigatan 29, Karlstad

    Zadzwoń do nas

    054-830 480

    Napisz do nas

    service@obdtuning.se

    © 2026 OBD Tuning Karlstad. Wszelkie prawa zastrzeżone.