Przejdź do treści
    OBD Tuning
    WYŚLIJ DO NAS
    WYŚLIJ DO NAS
    Strona główna
    Kody błędów
    VOLVO
    CEM-B1D0011
    VOLVO

    CEM-B1D0011 - Lefthand Low Beam Circuit. General Electrical Failures. Circuit short to ground

    Układ

    Centralny moduł elektroniczny (CEM)

    Modele Volvo, których dotyczy ten kod błędu

    Ten kod błędu ma różne znaczenie w zależności od modelu, rocznika lub silnika. Wybierz znaczenie, które dotyczy Twojego samochodu.

    Dotyczy następujących modeli:

    7 modeli

    S60 (2011–), S80 (2007–), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–)

    Pokaż modele wg rocznika i silnika (7)
    • Volvo S60 (2011–)2011–2015
    • Volvo S80 (2007–)2007–2015
    • Volvo V60 (2011–)2011–2015
    • Volvo V60 Cross Country (2015–)2015
    • Volvo V70 (2008–)2008–2015
    • Volvo XC60 (2009–)2009–2015
    • Volvo XC70 (2008–)2008–2015

    Co oznacza ten kod błędu?

    The central electronic module (CEM) powers the left low beam directly through an output. The code is set when the signal wire to the low beam lamp is shorted to ground, and The fault can therefore show both when you switch the low beam on and in a later drive.

    Możliwe przyczyny

    • The signal wire to the low beam lamp is shorted to ground

    Co możesz zrobić

    1. 1Clear the code and check whether it comes back after a new driving cycle with the low beam on
    2. 2Check that the fuse for the left low beam is intact
    3. 3Look for chafing on the signal wire to the left low beam lamp, especially where it may have touched metal
    4. 4Use a multimeter to check that the signal wire has no contact with ground (the bodywork)
    5. 5If the wire is intact, have a workshop with diagnostic equipment check the module output and the lamp

    Objawy, które możesz zauważyć3

    • The headlight does not work
    • Yellow warning symbol and text message in the display
    • The bulb failure warning in the instruments comes on or behaves abnormally

    Na co może wpływać usterka3

    • The function switches off during the driving cycle in which the fault is detected
    • After repeated driving cycles with the fault, the function is switched off permanently
    • Clearing the fault codes and starting a new driving cycle resets the output

    Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.

    OBD Tuning

    Wiodące centrum ekspertów Szwecji w elektronice motoryzacyjnej. Oferujemy profesjonalną optymalizację silnika, naprawę sterowników i diagnostykę z gwarancją 12 miesięcy.

    Usługi

    • Optymalizacja silnika
    • Naprawa sterownika
    • Klonowanie modułów
    • Zestaw wskaźników
    • SRS / Poduszka powietrzna
    • Immobilizer

    Baza danych & Diagnostyka

    • Baza danych sterowników
    • Katalog kodów DTC
    • Przewodniki diagnostyczne & Pomiary
    • Analizator błędów AI
    • Aktualności

    Producenci ECU

    • Bosch
    • Continental
    • Delphi
    • Delco
    • Denso
    • Magneti Marelli
    • Siemens / VDO
    • Keihin
    • Temic

    Firma

    • O nas
    • Kontakt
    • Partnerzy warsztatów
    • Przewodnik wysyłki
    • Gwarancja
    • FAQ
    • Regulamin
    • Polityka prywatności
    • Mapa strony

    • Optymalizacja silnika
    • Naprawa sterownika
    • Klonowanie modułów
    • Zestaw wskaźników
    • SRS / Poduszka powietrzna
    • Immobilizer

    • Baza danych sterowników
    • Katalog kodów DTC
    • Przewodniki diagnostyczne & Pomiary
    • Analizator błędów AI
    • Aktualności

    • Bosch
    • Continental
    • Delphi
    • Delco
    • Denso
    • Magneti Marelli
    • Siemens / VDO
    • Keihin
    • Temic

    • O nas
    • Kontakt
    • Partnerzy warsztatów
    • Przewodnik wysyłki
    • Gwarancja
    • FAQ
    • Regulamin
    • Polityka prywatności
    • Mapa strony

    Odwiedź nas

    Gjuterigatan 29, Karlstad

    Zadzwoń do nas

    054-830 480

    Napisz do nas

    service@obdtuning.se

    © 2026 OBD Tuning Karlstad. Wszelkie prawa zastrzeżone.