VOLVO
ECM-28A0 - Heated oxygen sensor (HO2S). Signal too low
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
8 modeliC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Pokaż modele wg rocznika i silnika (20)
- Volvo C30 (2007–2013)2007Tylko silnik: D5244T8, D5244T9
- Volvo C30 (2007–2013)2008–2010Tylko silnik: D5244T13, D5244T8, D5244T9
- Volvo C70 (2006–2013)2007Tylko silnik: D5244T8, D5244T9
- Volvo C70 (2006–2013)2008–2010Tylko silnik: D5244T13, D5244T8, D5244T9
- Volvo S40 (2004–2013)2006Tylko silnik: D5244T8
- Volvo S40 (2004–2013)2007Tylko silnik: D5244T8, D5244T9
- Volvo S40 (2004–2013)2008–2010Tylko silnik: D5244T13, D5244T8, D5244T9
- Volvo S60 (2001–2009)2006Tylko silnik: D5244T4, D5244T5, D5244T6, D5244T7
- Volvo S60 (2001–2009)2007–2009Tylko silnik: D5244T4, D5244T5, D5244T7
- Volvo V50 (2004–2013)2006Tylko silnik: D5244T8
- Volvo V50 (2004–2013)2007Tylko silnik: D5244T8, D5244T9
- Volvo V50 (2004–2013)2008–2010Tylko silnik: D5244T13, D5244T8, D5244T9
- Volvo V70 (2000–2008)2006Tylko silnik: D5244T4, D5244T5, D5244T6, D5244T7
- Volvo V70 (2000–2008)2007Tylko silnik: D5244T4, D5244T5, D5244T7
- Volvo V70 (2000–2008)2008Tylko silnik: D5244T5, D5244T7
- Volvo V70 XC / XC70 (2001–2007)2006–2007Tylko silnik: D5244T4
- Volvo XC90 (2003–)2006–2007Tylko silnik: D5244T4
- Volvo XC90 (2003–)2008–2010Tylko silnik: D5244T4, D5244T5
- Volvo XC90 (2003–)2011Tylko silnik: D5244T18, D5244T4, D5244T5
- Volvo XC90 (2003–)2012Wszystkie silniki oprócz: B5254T2, B6324S5
Co oznacza ten kod błędu?
Although the code is named signal too low, the control module has calculated an incorrect temperature for the oxygen sensor from its internal resistance, and the code is set when that calculated value is wrong. Causes may be a broken or shorted signal wire, a damaged sensor, or an internal fault in the control module.
Możliwe przyczyny
- Open circuit in the signal cable
- Short circuit between the signal cables
- Damaged oxygen sensor
- Fault inside the engine control module (ECM) itself
Co możesz zrobić
- 1Read the code, clear it and run the engine for a while to see whether it returns
- 2Switch off the ignition and check the oxygen sensor connections: they should be secure and free from play, contact resistance and oxidation
- 3With the car switched off, use a multimeter to check that the signal wire is not broken and the two signal wires are not shorted to each other
- 4If the connections and wiring are in order but the fault remains, have a workshop check the sensor and the control module with diagnostic equipment
Objawy, które możesz zauważyć1
- Message in the information display
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.