VOLVO
ECM-92D0 - Electronic throttle unit. Faulty signal
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
9 modeliC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Pokaż modele wg rocznika i silnika (23)
- Volvo C30 (2007–2013)2007Tylko silnik: B5254T3
- Volvo C30 (2007–2013)2008–2013Tylko silnik: B5254T7
- Volvo C70 (2006–2013)2006–2007Tylko silnik: B5254T3
- Volvo C70 (2006–2013)2008–2013Tylko silnik: B5254T7
- Volvo S40 (2004–2013)2005–2007Tylko silnik: B5254T3
- Volvo S40 (2004–2013)2008Tylko silnik: B5254T3, B5254T7
- Volvo S40 (2004–2013)2009–2012Tylko silnik: B5254T7
- Volvo S60 (2001–2009)2005–2006Tylko silnik: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2007Tylko silnik: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2008–2009Tylko silnik: B5204T5, B5244T5, B5254T2
- Volvo S80 (1999–2006)2005–2006Tylko silnik: B5204T5, B5244T4, B5254T2, B6294S2, B6294T
- Volvo V50 (2004–2013)2005–2007Tylko silnik: B5254T3
- Volvo V50 (2004–2013)2008–2012Tylko silnik: B5254T7
- Volvo V70 (2000–2008)2005Tylko silnik: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2006–2007Tylko silnik: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2008Tylko silnik: B5254T2
- Volvo V70 XC / XC70 (2001–2007)2005Wszystkie silniki oprócz: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Tylko silnik: B5244T4, B5254T2
- Volvo V70 XC / XC70 (2001–2007)2007Tylko silnik: B5254T2
- Volvo XC90 (2003–)2005–2006Tylko silnik: B5254T2, B6294T
- Volvo XC90 (2003–)2007–2012Tylko silnik: B5254T2
- Volvo XC90 (2003–)2013–2014Tylko silnik: B5254T9
- Volvo XC90 (2003–)2015
Co oznacza ten kod błędu?
The code is stored when the ignition has been on for some time without the ECM completing the throttle unit adaptation. This happens because the mechanical stop limit set for the throttle position sensor has been passed. Although the code is titled faulty signal, it concerns the adaptation.
Możliwe przyczyny
- The throttle sticks or is blocked by oil film or dust
- Contact resistance or oxidation in the connectors between the ECM and the throttle unit
- A damaged throttle unit
Co możesz zrobić
- 1Read the fault codes and deal first with any that are stored, as they may be why the adaptation cannot be completed
- 2Check the connectors between the ECM and the throttle unit: are they secure, and is there oxidation or corrosion
- 3Check that the throttle is not blocked by any object and not sticking. Clean as needed
- 4If you have a diagnostic tool: check in the parameters whether the adaptation has succeeded. If it shows OK, it is complete. The adaptation is done by a workshop
- 5If the fault remains, the throttle unit may be damaged and need replacing. The new unit must be adapted by a workshop
Objawy, które możesz zauważyć1
- Reduced engine performance
Na co może wpływać usterka2
- The ECM uses parameters from earlier successful adaptations
- The ECM cuts power to the throttle motor, and the throttle goes to its return position
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.