VOLVO
ECM-P004400 - HO2S Heater Control Circuit High (Bank 1, Sensor 3). General Failure Information. No sub type information
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
8 modeliS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–), XC70 (2008–)
Pokaż modele wg rocznika i silnika (15)
- Volvo S60 (2011–)2014–2015Tylko silnik: B4204T10, B4204T11, B4204T12, B4204T15, B4204T9
- Volvo S80 (2007–)2010Tylko silnik: B6324S2
- Volvo S80 (2007–)2011–2013Tylko silnik: B6324S4
- Volvo S80 (2007–)2014–2015Tylko silnik: B4204T11, B4204T12, B4204T15, B6324S4
- Volvo V40 (2013–)2015Tylko silnik: B4204T11
- Volvo V40 Cross Country (2013–)2015Tylko silnik: B4204T11
- Volvo V60 (2011–)2014–2015Tylko silnik: B4204T11, B4204T12, B4204T15, B4204T9
- Volvo V70 (2008–)2010Tylko silnik: B6324S2
- Volvo V70 (2008–)2014–2015Tylko silnik: B4204T11
- Volvo XC60 (2009–)2010Tylko silnik: B6324S2
- Volvo XC60 (2009–)2011–2013Tylko silnik: B6324S4
- Volvo XC60 (2009–)2014–2015Tylko silnik: B4204T10, B4204T11, B4204T12, B4204T15, B4204T9, B6324S4
- Volvo XC70 (2008–)2010Tylko silnik: B6324S2
- Volvo XC70 (2008–)2011–2013Tylko silnik: B6324S4
- Volvo XC70 (2008–)2014–2015Tylko silnik: B4204T11, B6324S4
Co oznacza ten kod błędu?
The engine control module checks the preheating circuit for the rear oxygen sensor, bank 1 sensor 3. The code is set when the circuit is short-circuited to supply voltage, meaning the lead has come into contact with a live wire. The fault can only be detected once the test has started and the conditions are met. Vehicles with two oxygen sensors cannot get this code.
Możliwe przyczyny
- The preheating supply lead is short-circuited to voltage
- Damaged rear heated oxygen sensor
Co możesz zrobić
- 1Make sure the fuses are intact. Their locations are on the fuse chart or in the instruction manual
- 2Read the fault status with a diagnostic tool after the diagnostic has run. If it shows active, the fault is still there
- 3Look for abrasion or pinch damage on the sensor lead, where it may have touched a live wire
- 4With a multimeter, check that the lead is not short-circuited to voltage
- 5If the wiring is intact but the fault remains, the rear oxygen sensor may be damaged and need replacing
Objawy, które możesz zauważyć2
- The malfunction indicator lamp lights up
- The Check engine lamp and other warning lamps may behave abnormally
Na co może wpływać usterka2
- The rear oxygen sensor does not preheat
- Control of the rear oxygen sensor is switched off
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.