Przejdź do treści
    OBD Tuning
    WYŚLIJ DO NAS
    WYŚLIJ DO NAS
    Strona główna
    Kody błędów
    VOLVO
    ECM-P005300
    VOLVO

    ECM-P005300 - HO2S Heater Resistance (Bank 1, Sensor 1). General Failure Information. No sub type information

    Układ

    Sterownik silnika (ECM)

    Modele Volvo, których dotyczy ten kod błędu

    Dotyczy następujących modeli:

    9 modeli

    C30 (2007–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V70 (2008–)

    Pokaż modele wg rocznika i silnika (9)
    • Volvo C30 (2007–2013)2011–2013Tylko silnik: D4162T
    • Volvo S40 (2004–2013)2011–2012Tylko silnik: D4162T
    • Volvo S60 (2011–)2011–2015Tylko silnik: D4162T
    • Volvo S80 (2007–)2012–2015Tylko silnik: D4162T
    • Volvo V40 (2013–)2013–2015Tylko silnik: D4162T
    • Volvo V40 Cross Country (2013–)2013–2015Tylko silnik: D4162T
    • Volvo V50 (2004–2013)2011–2012Tylko silnik: D4162T
    • Volvo V60 (2011–)2011–2015Tylko silnik: D4162T
    • Volvo V70 (2008–)2012–2015Tylko silnik: D4162T

    Co oznacza ten kod błędu?

    The oxygen sensor gives the engine control module information about the fuel and air mixture. The code concerns the signal to the preheating of the oxygen sensor on bank 1, sensor 1, which is wrong when the fault is set.

    Możliwe przyczyny

    • Contact resistance or oxidation in the terminals
    • Open circuit or short circuit in the wiring
    • Damaged oxygen sensor
    • Damaged engine control module

    Co możesz zrobić

    1. 1Make sure the fuses are intact. Their location is given in the instruction manual
    2. 2Read the fault code with a diagnostic tool with the ignition in position II and note whether it is active
    3. 3Check the connector to the oxygen sensor on bank 1 sensor 1 for contact resistance and oxidation
    4. 4With a multimeter, check that the wiring to the sensor has no open circuit and no short to ground
    5. 5Replace the oxygen sensor if the wiring is intact but the fault remains
    6. 6Have a workshop with diagnostic equipment check the engine control module if the sensor and wiring are intact

    Objawy, które możesz zauważyć2

    • The Check engine (malfunction indicator) lamp lights up or behaves abnormally
    • No other noticeable symptoms for the driver

    Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.

    OBD Tuning

    Wiodące centrum ekspertów Szwecji w elektronice motoryzacyjnej. Oferujemy profesjonalną optymalizację silnika, naprawę sterowników i diagnostykę z gwarancją 12 miesięcy.

    Usługi

    • Optymalizacja silnika
    • Naprawa sterownika
    • Klonowanie modułów
    • Zestaw wskaźników
    • SRS / Poduszka powietrzna
    • Immobilizer

    Baza danych & Diagnostyka

    • Baza danych sterowników
    • Katalog kodów DTC
    • Przewodniki diagnostyczne & Pomiary
    • Analizator błędów AI
    • Aktualności

    Producenci ECU

    • Bosch
    • Continental
    • Delphi
    • Delco
    • Denso
    • Magneti Marelli
    • Siemens / VDO
    • Keihin
    • Temic

    Firma

    • O nas
    • Kontakt
    • Partnerzy warsztatów
    • Przewodnik wysyłki
    • Gwarancja
    • FAQ
    • Regulamin
    • Polityka prywatności
    • Mapa strony

    • Optymalizacja silnika
    • Naprawa sterownika
    • Klonowanie modułów
    • Zestaw wskaźników
    • SRS / Poduszka powietrzna
    • Immobilizer

    • Baza danych sterowników
    • Katalog kodów DTC
    • Przewodniki diagnostyczne & Pomiary
    • Analizator błędów AI
    • Aktualności

    • Bosch
    • Continental
    • Delphi
    • Delco
    • Denso
    • Magneti Marelli
    • Siemens / VDO
    • Keihin
    • Temic

    • O nas
    • Kontakt
    • Partnerzy warsztatów
    • Przewodnik wysyłki
    • Gwarancja
    • FAQ
    • Regulamin
    • Polityka prywatności
    • Mapa strony

    Odwiedź nas

    Gjuterigatan 29, Karlstad

    Zadzwoń do nas

    054-830 480

    Napisz do nas

    service@obdtuning.se

    © 2026 OBD Tuning Karlstad. Wszelkie prawa zastrzeżone.