VOLVO
ECM-P006A62 - MAP - Mass or Volume Air Flow Correlation. Algorithm Based Failures. Signal compare failure
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
7 modeliS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Pokaż modele wg rocznika i silnika (20)
- Volvo S60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Tylko silnik: B4204T6
- Volvo S80 (2007–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Tylko silnik: B4164T
- Volvo V40 (2013–)2013Tylko silnik: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Tylko silnik: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Tylko silnik: B4164T
- Volvo V60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Tylko silnik: B4204T6
- Volvo V70 (2008–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Tylko silnik: B4164T, B4164T2
- Volvo XC60 (2009–)2010Tylko silnik: B4204T6
- Volvo XC60 (2009–)2011–2012Tylko silnik: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Tylko silnik: B4204T7
Co oznacza ten kod błędu?
The engine control module works out the expected air mass from several parameters and compares it with the reading from the mass air flow sensor. The code is set when the air mass correction factor drops too far while the lambda adaptation sits outside a set band.
Możliwe przyczyny
- Contact resistance or oxidation in the connectors of the mass air flow sensor
- Air leakage in the intake system
- Blocked intake system
- Damaged mass air flow sensor
Co możesz zrobić
- 1Check the mass air flow sensor connector for contact resistance and oxidation
- 2Check the hoses between the mass air flow sensor and the throttle unit for leaks, damage and loose connections
- 3Check that the intake system is not blocked, for example by contamination in the throttle
- 4If you have a diagnostic tool, read the air mass in live data at idle and when the throttle is opened. The value should follow the throttle
- 5Have a workshop check the mass air flow sensor if the fault remains after checking the intake system
Objawy, które możesz zauważyć1
- Poor performance and lack of power while driving
Na co może wpływać usterka3
- A calculated boost pressure and a calculated air mass are used
- Control of the rear oxygen sensor is switched off
- The misfire diagnostic is switched off
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.