VOLVO
ECM-P007D12 - Charge Air Cooler Temperature Sensor Circuit High (Bank 1). General Electrical Failures. Circuit short to battery
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
7 modeliS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Pokaż modele wg rocznika i silnika (20)
- Volvo S60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Tylko silnik: B4204T6
- Volvo S80 (2007–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Tylko silnik: B4164T
- Volvo V40 (2013–)2013Tylko silnik: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Tylko silnik: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Tylko silnik: B4164T
- Volvo V60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Tylko silnik: B4204T6
- Volvo V70 (2008–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Tylko silnik: B4164T, B4164T2
- Volvo XC60 (2009–)2010Tylko silnik: B4204T6
- Volvo XC60 (2009–)2011–2012Tylko silnik: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Tylko silnik: B4204T7
Co oznacza ten kod błędu?
The boost pressure sensor (TMAP) measures boost pressure and temperature at the charge air cooler. The fault code is set when the signal from the sensor is above a limit. The cause can be a signal wire shorted to voltage, an open circuit in the signal wire or a damaged sensor.
Możliwe przyczyny
- Open circuit in the signal wire to the boost pressure sensor
- Signal wire shorted to voltage
- Damaged boost pressure sensor (TMAP)
Co możesz zrobić
- 1Use a multimeter to check that the signal wire to the boost pressure sensor has no voltage with the ignition off
- 2Check that the sensor connector is secure and not damaged
- 3Look for wiring that appears chafed or pinched at the sensor and along the route to it
- 4If you have a diagnostic tool: read the boost pressure sensor temperature in live data with the engine running and check whether it reads an unreasonably high value
- 5Have a workshop check the sensor if the wiring is intact and the fault remains
Objawy, które możesz zauważyć1
- The Check engine warning lamp lights up
Na co może wpływać usterka1
- The engine control module uses a calculated value instead of the measured temperature
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.