VOLVO
ECM-P008000 - Exhaust Valve Control Circuit High (Bank 1). General Failure Information. No sub type information
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
10 modeliS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Pokaż modele wg rocznika i silnika (28)
- Volvo S60 (2011–)2011–2012Tylko silnik: B5254T5
- Volvo S60 (2011–)2013Tylko silnik: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo S60 (2011–)2014–2015Tylko silnik: B4204T10, B4204T11, B4204T12, B4204T15, B4204T9, B5204T8, B5204T9, B5254T12, B5254T14
- Volvo S80 (2007–)2007–2008Tylko silnik: B5254T6, B8444S
- Volvo S80 (2007–)2009Tylko silnik: B5254T6, B5254T8, B8444S
- Volvo S80 (2007–)2010–2011Tylko silnik: B5254T10, B5254T11, B5254T8, B8444S
- Volvo S80 (2007–)2012Tylko silnik: B5254T10
- Volvo S80 (2007–)2013Tylko silnik: B5254T12, B5254T14
- Volvo S80 (2007–)2014Tylko silnik: B4204T11, B4204T12, B4204T15, B5254T12, B5254T14
- Volvo S80 (2007–)2015Tylko silnik: B4204T11, B4204T12, B4204T15
- Volvo V40 (2013–)2013–2014Tylko silnik: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V40 (2013–)2015Tylko silnik: B4204T11, B5204T8, B5204T9
- Volvo V40 Cross Country (2013–)2013–2014Tylko silnik: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V40 Cross Country (2013–)2015Wszystkie silniki oprócz: B4164T, D4162T, D4204T14, D5204T6
- Volvo V60 (2011–)2013Tylko silnik: B5204T8, B5204T9
- Volvo V60 (2011–)2014Tylko silnik: B4204T11, B4204T12, B4204T15, B4204T9, B5204T8, B5204T9, B5254T12
- Volvo V60 (2011–)2015Tylko silnik: B4204T11, B4204T12, B4204T15, B4204T9, B5204T9, B5254T12
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008Tylko silnik: B5254T6
- Volvo V70 (2008–)2009Tylko silnik: B5254T6, B5254T8
- Volvo V70 (2008–)2010–2011Tylko silnik: B5254T10, B5254T11
- Volvo V70 (2008–)2012Tylko silnik: B5254T10
- Volvo V70 (2008–)2013Tylko silnik: B5204T9
- Volvo V70 (2008–)2014–2015Tylko silnik: B4204T11, B5204T9
- Volvo XC60 (2009–)2014Tylko silnik: B4204T10, B4204T11, B4204T12, B4204T15, B4204T9
- Volvo XC60 (2009–)2015Tylko silnik: B4204T10, B4204T11, B4204T12, B4204T15, B4204T9, B5204T9, B5254T12, B5254T14
- Volvo XC70 (2008–)2014–2015Tylko silnik: B4204T11
- Volvo XC90 (2003–)2005–2011Tylko silnik: B8444S
Co oznacza ten kod błędu?
The engine control module (ECM) adjusts the exhaust camshaft position with a changeover valve on bank 1, the cylinder row nearest the front. The fault code is set when the control signal to the valve is too high. The causes are a signal wire shorted to voltage or a damaged valve.
Możliwe przyczyny
- Signal wire to the changeover valve shorted to voltage
- Damaged exhaust camshaft changeover valve
Co możesz zrobić
- 1Read off the fault code and check whether the fault is active right now or has only been present earlier
- 2Check that the fuses for the engine control circuits are intact
- 3Use a multimeter to check whether the signal wire to the exhaust valve has contact with voltage with the ignition off
- 4Check the connector at the exhaust valve and the wiring leading to it
- 5If you have a diagnostic tool, activate the exhaust valve and listen or feel for it responding
- 6If the fault returns after these checks, have a workshop check the valve
Objawy, które możesz zauważyć4
- Check engine lamp (MIL) lights up
- Uneven idle
- Poor performance and lack of power
- The engine can stall while driving, during acceleration, deceleration or at steady speed
Na co może wpływać usterka1
- Exhaust camshaft control is switched off
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.