VOLVO
ECM-P008B22 - Low Pressure Fuel System Pressure - Too High. General Signal Failures. Signal too high
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
7 modeliS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Pokaż modele wg rocznika i silnika (20)
- Volvo S60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Tylko silnik: B4204T6
- Volvo S80 (2007–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Tylko silnik: B4164T
- Volvo V40 (2013–)2013Tylko silnik: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Tylko silnik: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Tylko silnik: B4164T
- Volvo V60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Tylko silnik: B4204T6
- Volvo V70 (2008–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Tylko silnik: B4164T, B4164T2
- Volvo XC60 (2009–)2010Tylko silnik: B4204T6
- Volvo XC60 (2009–)2011–2012Tylko silnik: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Tylko silnik: B4204T7
Co oznacza ten kod błędu?
The engine control module (ECM) requests a fuel pressure and controls the fuel pump through the fuel pump control module. The fault code is set when the pressure reported by the sensor is too high compared with the requested pressure for a certain time, while the engine runs. The cause can be a supply wire shorted to voltage, or a damaged sensor or pump control module.
Możliwe przyczyny
- Supply wire to the fuel pump shorted to voltage
- Damaged fuel pressure sensor
- Damaged fuel pump control module
Co możesz zrobić
- 1Use a multimeter to check that the supply wire to the fuel pump has no voltage with the ignition off
- 2Make sure the connectors to the fuel pump and the sensor are secure and clean
- 3If you have a diagnostic tool: compare the fuel pressure in live data with the requested pressure while the engine runs
- 4Have a workshop measure the fuel pressure with a gauge and, if it is wrong, check the sensor and the fuel pump control module
Objawy, które możesz zauważyć3
- Check engine lamp (MIL) lights up
- The car lacks power and performs poorly
- The engine can stall while driving
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.