VOLVO
ECM-P010817 - Manifold Absolute Pressure/BARO Sensor High. General Electrical Failures. Circuit voltage above threshold
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
7 modeliS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Pokaż modele wg rocznika i silnika (20)
- Volvo S60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Tylko silnik: B4204T6
- Volvo S80 (2007–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Tylko silnik: B4164T
- Volvo V40 (2013–)2013Tylko silnik: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Tylko silnik: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Tylko silnik: B4164T
- Volvo V60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Tylko silnik: B4204T6
- Volvo V70 (2008–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Tylko silnik: B4164T, B4164T2
- Volvo XC60 (2009–)2010Tylko silnik: B4204T6
- Volvo XC60 (2009–)2011–2012Tylko silnik: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Tylko silnik: B4204T7
Co oznacza ten kod błędu?
The ECM measures the intake pressure with an air pressure sensor and checks the sensor's DC voltage. The code is stored when an incorrect value lasts for a set time or over three or more consecutive drive cycles.
Możliwe przyczyny
- Break in the signal or ground wire
- Contact resistance and oxidation in the connections
- Signal wire shorted to supply voltage
- Air pressure sensor in the intake pipe is damaged
Co możesz zrobić
- 1Read and note the code, clear it and road test to see whether it returns
- 2With diagnostic equipment and the ignition on, compare the intake pressure in live data with ambient pressure; a clear difference suggests a faulty sensor
- 3Check that the connector at the sensor sits firmly and is free from oxidation and contact resistance
- 4With a multimeter, check that the signal wire is not shorted to supply voltage or ground
- 5If the fault remains and the sensor reading differs, have a workshop replace the sensor
Objawy, które możesz zauważyć1
- Engine warning lamp (check engine) lit or behaving abnormally
Na co może wpływać usterka1
- The sensor signal is replaced by a constant intake air pressure value
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.