VOLVO
ECM-P01162A - Engine Coolant Temperature Sensor 1 Circuit Range/Performance. General Signal Failures. Signal stuck in range
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
8 modeliS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–), XC70 (2008–)
Pokaż modele wg rocznika i silnika (34)
- Volvo S60 (2011–)2011Tylko silnik: D5204T2, D5244T10
- Volvo S60 (2011–)2012Tylko silnik: D5204T3, D5244T11, D5244T15
- Volvo S60 (2011–)2013Tylko silnik: D5204T7
- Volvo S60 (2011–)2014–2015Tylko silnik: B4204T10, B4204T11, B4204T12, B4204T15, B4204T9, D4204T5, D5204T7
- Volvo S80 (2007–)2009Tylko silnik: D5244T10
- Volvo S80 (2007–)2010Tylko silnik: D5244T10, D5244T14, D5244T19
- Volvo S80 (2007–)2011Tylko silnik: D5204T2, D5244T10
- Volvo S80 (2007–)2012Tylko silnik: D5204T3, D5244T11, D5244T15
- Volvo S80 (2007–)2013Tylko silnik: D5204T7
- Volvo S80 (2007–)2014Tylko silnik: B4204T11, B4204T12, B4204T15, D4204T5, D5204T7
- Volvo S80 (2007–)2015Tylko silnik: B4204T11, B4204T12, B4204T15, D4204T5
- Volvo V40 (2013–)2013–2014Tylko silnik: D5204T4, D5204T6
- Volvo V40 (2013–)2015Tylko silnik: B4204T11, D4204T14, D5204T6
- Volvo V40 Cross Country (2013–)2013–2014Tylko silnik: D5204T4, D5204T6
- Volvo V40 Cross Country (2013–)2015Tylko silnik: B4204T11, D4204T14, D5204T6
- Volvo V60 (2011–)2011Tylko silnik: D5204T2, D5244T10
- Volvo V60 (2011–)2012Tylko silnik: D5204T3, D5244T11, D5244T15
- Volvo V60 (2011–)2013Tylko silnik: D5204T7, D82PHEV
- Volvo V60 (2011–)2014Tylko silnik: B4204T11, B4204T12, B4204T15, B4204T9, D4204T5, D5204T7, D82PHEV
- Volvo V60 (2011–)2015Tylko silnik: B4204T11, B4204T12, B4204T15, B4204T9, D4204T5, D5204T7, D82PHEV, D87PHEV
- Volvo V70 (2008–)2009Tylko silnik: D5244T10
- Volvo V70 (2008–)2010Tylko silnik: D5244T10, D5244T14, D5244T19
- Volvo V70 (2008–)2011Tylko silnik: D5204T2, D5244T10
- Volvo V70 (2008–)2012Tylko silnik: D5204T3, D5244T11, D5244T15
- Volvo V70 (2008–)2013Tylko silnik: D5204T7
- Volvo V70 (2008–)2014–2015Tylko silnik: B4204T11, D4204T5, D5204T7
- Volvo XC60 (2009–)2010Tylko silnik: D5244T10, D5244T14, D5244T16
- Volvo XC60 (2009–)2011Tylko silnik: D5204T2, D5244T10, D5244T16
- Volvo XC60 (2009–)2012Tylko silnik: D5204T3, D5244T11, D5244T15, D5244T17
- Volvo XC60 (2009–)2014–2015Tylko silnik: B4204T10, B4204T11, B4204T12, B4204T15, B4204T9, D4204T5
- Volvo XC70 (2008–)2010Tylko silnik: D5244T10, D5244T14, D5244T16
- Volvo XC70 (2008–)2011Tylko silnik: D5204T2, D5244T10, D5244T16
- Volvo XC70 (2008–)2012Wszystkie silniki oprócz: B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2014–2015Tylko silnik: B4204T11, D4204T5
Co oznacza ten kod błędu?
The engine control module (ECM) checks the function of the coolant temperature sensor during warm-up after a cold start. If the value from the sensor has changed too little compared with the start temperature, the fault code is set.
Możliwe przyczyny
- Loose connection or oxidation in the connector
- Open circuit on the control signal lead
- Damaged battery relay
- Damaged coolant temperature sensor
- Contact resistance or oxidation in the connections
Co możesz zrobić
- 1Read the fault code status with the ignition on and check whether the fault is active. Then clear the code and road test the vehicle from a cold start
- 2Check that the fuses are intact
- 3Check the connector at the engine temperature sensor for looseness, contact resistance and oxidation
- 4If you have a diagnostic tool: read the engine temperature sensor signal in live data. An unreasonable value means a permanent fault, while a reasonable one means it is not active now
- 5If the connector is in order and the fault remains, have a workshop check the sensor, the battery relay and the wiring
Objawy, które możesz zauważyć4
- Automatic engine start/stop does not work while driving
- Automatic engine start/stop does not work at idle
- The Check engine light comes on or behaves abnormally
- The engine is difficult to start and cranks slowly on starting
Na co może wpływać usterka2
- The automatic engine start/stop function is switched off
- The control module falls back on a default value or a calculation model
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.