VOLVO
ECM-P022023 - Throttle/Pedal Position Switch B Circuit. General Signal Failures. Signal stuck low
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
10 modeliS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Pokaż modele wg rocznika i silnika (30)
- Volvo S60 (2011–)2011–2012Tylko silnik: B6304T4
- Volvo S60 (2011–)2013–2014Tylko silnik: B5204T8, B5204T9, B5254T12, B5254T14, B6304T4
- Volvo S60 (2011–)2015Tylko silnik: B5204T8, B5204T9, B5254T12, B5254T14, B6304T3, B6304T4, B6304T5
- Volvo S80 (2007–)2007Tylko silnik: B6324S, B8444S
- Volvo S80 (2007–)2008–2009Tylko silnik: B6304T2, B6324S, B8444S
- Volvo S80 (2007–)2010Tylko silnik: B6304T2, B6324S, B6324S2
- Volvo S80 (2007–)2011–2012, 2015Tylko silnik: B6304T4, B6324S4, B6324S5
- Volvo S80 (2007–)2013–2014Tylko silnik: B5254T12, B5254T14, B6304T4, B6324S4, B6324S5
- Volvo V40 (2013–)2013–2014Tylko silnik: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V40 (2013–)2015Tylko silnik: B5204T8, B5204T9
- Volvo V40 Cross Country (2013–)2013–2015Tylko silnik: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V60 (2011–)2011–2012Tylko silnik: B6304T4
- Volvo V60 (2011–)2013Tylko silnik: B5204T8, B5204T9, B6304T4
- Volvo V60 (2011–)2014Tylko silnik: B5204T8, B5204T9, B5254T12, B6304T4
- Volvo V60 (2011–)2015Tylko silnik: B5204T9, B5254T12, B6304T3, B6304T4, B6304T5
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008–2009Tylko silnik: B6304T2, B6324S
- Volvo V70 (2008–)2010Tylko silnik: B6304T2, B6324S, B6324S2
- Volvo V70 (2008–)2011–2012Tylko silnik: B6304T4, B6324S5
- Volvo V70 (2008–)2013–2014Tylko silnik: B5204T9, B6304T4, B6324S5
- Volvo V70 (2008–)2015Tylko silnik: B5204T9, B6304T4
- Volvo XC60 (2009–)2009Tylko silnik: B6304T2
- Volvo XC60 (2009–)2010Tylko silnik: B6304T2, B6324S, B6324S2
- Volvo XC60 (2009–)2011–2014Tylko silnik: B6304T4, B6324S4, B6324S5
- Volvo XC60 (2009–)2015Tylko silnik: B5204T9, B5254T12, B5254T14, B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2008Tylko silnik: B6324S
- Volvo XC70 (2008–)2009Tylko silnik: B6304T2, B6324S
- Volvo XC70 (2008–)2010Tylko silnik: B6304T2, B6324S, B6324S2
- Volvo XC70 (2008–)2011–2015Tylko silnik: B6304T4, B6324S4, B6324S5
- Volvo XC90 (2003–)2007–2010Tylko silnik: B6324S
Co oznacza ten kod błędu?
Although the code is named switch B circuit, it applies to the signal from the accelerator pedal position sensor. The signal stays low for a longer period and therefore does not follow the pedal movement. The fault is first registered in the central electronic module (CEM), so the root fault may be there.
Możliwe przyczyny
- Signal wire shorted to ground
- Damaged accelerator pedal position sensor
- Fault in the central electronic module (CEM), which registers the fault first
Co możesz zrobić
- 1Read the codes in all control modules, not only the engine control module. If a code is present in the CEM, deal with it first
- 2Check that the fuses are intact. Fuse locations are shown in the owner's manual
- 3Look at the accelerator pedal connector and wiring for loose connections, corrosion and chafed areas
- 4Use a multimeter to check that the signal wire from the pedal is not shorted to ground
- 5If you have a diagnostic tool: check whether the accelerator pedal position in live data stays at the same low value when the pedal is pressed
- 6If the fault remains after these checks, have a workshop check the CEM and the accelerator pedal sensor with diagnostic equipment. The code is only cleared once the root fault is fixed
Objawy, które możesz zauważyć2
- Accelerator pedal ignored during braking
- Warning symbol and message in the display
Na co może wpływać usterka1
- When the brake pedal is pressed at the same time, the accelerator is treated as released
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.