VOLVO
ECM-P022024 - Throttle/Pedal Position Switch B Circuit. General Signal Failures. Signal stuck high
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
10 modeliS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Pokaż modele wg rocznika i silnika (30)
- Volvo S60 (2011–)2011–2012Tylko silnik: B6304T4
- Volvo S60 (2011–)2013–2014Tylko silnik: B5204T8, B5204T9, B5254T12, B5254T14, B6304T4
- Volvo S60 (2011–)2015Tylko silnik: B5204T8, B5204T9, B5254T12, B5254T14, B6304T3, B6304T4, B6304T5
- Volvo S80 (2007–)2007Tylko silnik: B6324S, B8444S
- Volvo S80 (2007–)2008–2009Tylko silnik: B6304T2, B6324S, B8444S
- Volvo S80 (2007–)2010Tylko silnik: B6304T2, B6324S, B6324S2
- Volvo S80 (2007–)2011–2012, 2015Tylko silnik: B6304T4, B6324S4, B6324S5
- Volvo S80 (2007–)2013–2014Tylko silnik: B5254T12, B5254T14, B6304T4, B6324S4, B6324S5
- Volvo V40 (2013–)2013–2014Tylko silnik: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V40 (2013–)2015Tylko silnik: B5204T8, B5204T9
- Volvo V40 Cross Country (2013–)2013–2015Tylko silnik: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V60 (2011–)2011–2012Tylko silnik: B6304T4
- Volvo V60 (2011–)2013Tylko silnik: B5204T8, B5204T9, B6304T4
- Volvo V60 (2011–)2014Tylko silnik: B5204T8, B5204T9, B5254T12, B6304T4
- Volvo V60 (2011–)2015Tylko silnik: B5204T9, B5254T12, B6304T3, B6304T4, B6304T5
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008–2009Tylko silnik: B6304T2, B6324S
- Volvo V70 (2008–)2010Tylko silnik: B6304T2, B6324S, B6324S2
- Volvo V70 (2008–)2011–2012Tylko silnik: B6304T4, B6324S5
- Volvo V70 (2008–)2013–2014Tylko silnik: B5204T9, B6304T4, B6324S5
- Volvo V70 (2008–)2015Tylko silnik: B5204T9, B6304T4
- Volvo XC60 (2009–)2009Tylko silnik: B6304T2
- Volvo XC60 (2009–)2010Tylko silnik: B6304T2, B6324S, B6324S2
- Volvo XC60 (2009–)2011–2014Tylko silnik: B6304T4, B6324S4, B6324S5
- Volvo XC60 (2009–)2015Tylko silnik: B5204T9, B5254T12, B5254T14, B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2008Tylko silnik: B6324S
- Volvo XC70 (2008–)2009Tylko silnik: B6304T2, B6324S
- Volvo XC70 (2008–)2010Tylko silnik: B6304T2, B6324S, B6324S2
- Volvo XC70 (2008–)2011–2015Tylko silnik: B6304T4, B6324S4, B6324S5
- Volvo XC90 (2003–)2007–2010Tylko silnik: B6324S
Co oznacza ten kod błędu?
Although the code is named switch B circuit, it applies to the signal from the accelerator pedal position sensor. The signal stays high all the time and does not change when the pedal is moved, so the reported pedal position is wrong. The fault is first registered in the central electronic module (CEM), so the root fault may be there.
Możliwe przyczyny
- Damaged accelerator pedal position sensor
- Fault in the central electronic module (CEM), which registers the fault first
Co możesz zrobić
- 1Read the codes in all control modules, not only the engine control module. If a code is present in the CEM, deal with it first
- 2Check that the fuses are intact. Fuse locations are shown in the owner's manual
- 3Look at the accelerator pedal connector and wiring for chafing, pinched areas and loose connections
- 4If you have a diagnostic tool: check whether the accelerator pedal position in live data stays at a high value when the pedal is released
- 5If the fault remains after these checks, have a workshop check the CEM and the accelerator pedal sensor with diagnostic equipment
Objawy, które możesz zauważyć2
- Accelerator pedal ignored when the brake is applied
- Warning symbol and message in the display
Na co może wpływać usterka1
- When the brake pedal is pressed at the same time, the accelerator is treated as released
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.