VOLVO
ECM-P030192 - Cylinder 1 Misfire Detected. Component Failures. Performance or incorrect operation
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
7 modeliS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Pokaż modele wg rocznika i silnika (27)
- Volvo S60 (2011–)2011Wszystkie silniki oprócz: B6304T4, D4162T, D5204T2, D5244T10
- Volvo S60 (2011–)2012Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7, B5254T5
- Volvo S60 (2011–)2013–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2007–2008Tylko silnik: B5254T6
- Volvo S80 (2007–)2009Tylko silnik: B5254T6, B5254T8
- Volvo S80 (2007–)2010Tylko silnik: B4204T6, B5254T10, B5254T11, B5254T8
- Volvo S80 (2007–)2011Tylko silnik: B4164T, B4204T6, B4204T7, B5254T10, B5254T11, B5254T8
- Volvo S80 (2007–)2012Tylko silnik: B4164T, B4164T2, B4204T6, B4204T7, B5254T10
- Volvo S80 (2007–)2013–2014Tylko silnik: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Tylko silnik: B4164T
- Volvo V40 (2013–)2013Tylko silnik: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Tylko silnik: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Tylko silnik: B4164T
- Volvo V60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2008Tylko silnik: B5254T6
- Volvo V70 (2008–)2009Tylko silnik: B5254T6, B5254T8
- Volvo V70 (2008–)2010Tylko silnik: B4204T6, B5254T10, B5254T11
- Volvo V70 (2008–)2011Tylko silnik: B4164T, B4204T6, B4204T7, B5254T10, B5254T11
- Volvo V70 (2008–)2012Tylko silnik: B4164T, B4164T2, B4204T7, B5254T10
- Volvo V70 (2008–)2013–2014Tylko silnik: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Tylko silnik: B4164T, B4164T2
- Volvo XC60 (2009–)2010Tylko silnik: B4204T6
- Volvo XC60 (2009–)2011–2012Tylko silnik: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Tylko silnik: B4204T7
Co oznacza ten kod błędu?
If the engine control module (ECM) detects emission-related misfires on cylinder 1 during the first period after engine start, the fault code is stored. The code points to cylinder 1 and shows that the misfire occurs just after starting, and it has its own fault-tracing sequence.
Możliwe przyczyny
- Low fuel level
- The engine does not reach operating temperature between several cold starts
- Contaminated or incorrect fuel
- Air leak
- Damaged ignition coil
- Incorrectly calculated ethanol content
Co możesz zrobić
- 1Read the fault codes; codes for camshaft control or the camshaft control valve are traced first
- 2Check that the fuel that has been filled is the correct type and that the fuel level is sufficient
- 3Make sure the engine oil is at the right level and that the intake system is not leaking
- 4Check the ignition coil on cylinder 1 and its connectors and wiring for damage or oxidation
- 5If you have a diagnostic tool: read the misfire counter for cylinder 1 with the engine running and see whether it differs from the others
- 6Have a workshop with diagnostic equipment check the crankcase ventilation, the compression and the fuel pressure
Objawy, które możesz zauważyć5
- The engine starts with difficulty
- Uneven idle
- Reduced performance and lack of power
- The engine hesitates or surges when driven
- The Check engine light lights up or behaves abnormally
Na co może wpływać usterka2
- Rear oxygen sensor control is switched off
- Lambda control is switched off
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.