VOLVO
ECM-P032815 - Knock Sensor 1 Circuit High (Bank 1). General Electrical Failures. Circuit short to battery or open
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
7 modeliS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Pokaż modele wg rocznika i silnika (20)
- Volvo S60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Tylko silnik: B4204T6
- Volvo S80 (2007–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Tylko silnik: B4164T
- Volvo V40 (2013–)2013Tylko silnik: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Tylko silnik: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Tylko silnik: B4164T
- Volvo V60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Tylko silnik: B4204T6
- Volvo V70 (2008–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Tylko silnik: B4164T, B4164T2
- Volvo XC60 (2009–)2010Tylko silnik: B4204T6
- Volvo XC60 (2009–)2011–2012Tylko silnik: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Tylko silnik: B4204T7
Co oznacza ten kod błędu?
The engine control module (ECM) monitors the signal from the left knock sensor and sets the fault code when the signal is too high. This can be caused by a signal cable short-circuited to voltage or by an open circuit. An incorrectly fitted or damaged knock sensor can also produce the fault code.
Możliwe przyczyny
- Signal cable short-circuited to voltage
- Incorrectly fitted knock sensor
- Damaged knock sensor
Co możesz zrobić
- 1Clear the fault code and test drive the car to see whether it returns
- 2Check that the wiring to the left knock sensor is complete, with no breaks or chafing, and that the plug is firmly connected
- 3With a multimeter, confirm that the cable is unbroken and has no contact with the positive supply
- 4Check that the left knock sensor is correctly fitted
- 5Have a workshop with diagnostic equipment check the sensor and the wiring and replace the knock sensor if needed
Objawy, które możesz zauważyć1
- Poor performance and lack of power while driving
Na co może wpływać usterka2
- Ignition timing is retarded as a safety measure
- Boost pressure is reduced
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.