VOLVO
ECM-P033211 - Knock Sensor 2 Circuit Low (Bank 2). General Electrical Failures. Circuit short to ground
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
7 modeliS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Pokaż modele wg rocznika i silnika (20)
- Volvo S60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Tylko silnik: B4204T6
- Volvo S80 (2007–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Tylko silnik: B4164T
- Volvo V40 (2013–)2013Tylko silnik: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Tylko silnik: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Tylko silnik: B4164T
- Volvo V60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Tylko silnik: B4204T6
- Volvo V70 (2008–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Tylko silnik: B4164T, B4164T2
- Volvo XC60 (2009–)2010Tylko silnik: B4204T6
- Volvo XC60 (2009–)2011–2012Tylko silnik: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Tylko silnik: B4204T7
Co oznacza ten kod błędu?
The signal from the right knock sensor is too low. The engine control module (ECM) compares the signal with limits and sets the fault code when it deviates. A signal cable that has been short-circuited to ground is one possible cause. Poor contact, a break or a damaged sensor can produce the same fault code.
Możliwe przyczyny
- Signal cable short-circuited to ground
- Contact resistance in the knock sensor connections
- Break in the signal cable
- Short circuit between the knock sensors' signal cables
- Damaged knock sensor
Co możesz zrobić
- 1Read the fault code, clear it and test drive the car
- 2Check the signal cable from the right knock sensor for a short to ground; with a multimeter, confirm that the cable has no contact with the body
- 3Check the connections to the right knock sensor for contact resistance and oxidation
- 4If you have a diagnostic tool: read the knock signal from the right sensor in live data with the engine running and see whether it is too low
- 5Have a workshop with diagnostic equipment check the wiring and replace the knock sensor if needed
Objawy, które możesz zauważyć1
- Poor performance and lack of power while driving
Na co może wpływać usterka2
- Ignition timing is retarded as a safety measure
- Boost pressure is reduced
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.