Przejdź do treści
    OBD Tuning
    WYŚLIJ DO NAS
    WYŚLIJ DO NAS
    Strona główna
    Kody błędów
    VOLVO
    ECM-P033800
    VOLVO

    ECM-P033800 - Crankshaft Position Sensor A Circuit High Input. General Failure Information. No sub type information

    Układ

    Sterownik silnika (ECM)

    Modele Volvo, których dotyczy ten kod błędu

    Dotyczy następujących modeli:

    3 modele

    S60 (2011–), S80 (2007–), V70 (2008–)

    Pokaż modele wg rocznika i silnika (9)
    • Volvo S60 (2011–)2011–2012Tylko silnik: B5254T5
    • Volvo S80 (2007–)2007–2008Tylko silnik: B5254T6
    • Volvo S80 (2007–)2009Tylko silnik: B5254T6, B5254T8
    • Volvo S80 (2007–)2010–2011Tylko silnik: B5254T10, B5254T11, B5254T8
    • Volvo S80 (2007–)2012Tylko silnik: B5254T10
    • Volvo V70 (2008–)2008Tylko silnik: B5254T6
    • Volvo V70 (2008–)2009Tylko silnik: B5254T6, B5254T8
    • Volvo V70 (2008–)2010–2011Tylko silnik: B5254T10, B5254T11
    • Volvo V70 (2008–)2012Tylko silnik: B5254T10

    Co oznacza ten kod błędu?

    The engine control module (ECM) counts the teeth on the flywheel using the signal from the crankshaft position sensor. The fault is stored when the ECM counts at least one tooth too many over a set number of engine revolutions. The code does not say which type of fault it is.

    Możliwe przyczyny

    • Signal interference
    • Damaged flywheel or ring gear

    Co możesz zrobić

    1. 1If you have a diagnostic tool, start the engine and read the fault status. 'Fault found' means the fault is permanent.
    2. 2Check that the fuses are intact.
    3. 3Check that the crankshaft position sensor is correctly fitted in the right position and is not damaged or dirty.
    4. 4Check that no cable with high current draw, such as the starter motor cable, lies too close to the sensor or its wiring.
    5. 5If you have a diagnostic tool, follow the engine speed in live data while the engine runs and check that the value is steady.
    6. 6If the fault remains, have a workshop check the flywheel and the carrier plate for damage.

    Objawy, które możesz zauważyć2

    • Engine is hard to start
    • Poor performance

    Na co może wpływać usterka2

    • If the camshaft sensor has been adapted, the ECM uses its signal instead
    • Variable valve timing (VVT) control is blocked

    Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.

    OBD Tuning

    Wiodące centrum ekspertów Szwecji w elektronice motoryzacyjnej. Oferujemy profesjonalną optymalizację silnika, naprawę sterowników i diagnostykę z gwarancją 12 miesięcy.

    Usługi

    • Optymalizacja silnika
    • Naprawa sterownika
    • Klonowanie modułów
    • Zestaw wskaźników
    • SRS / Poduszka powietrzna
    • Immobilizer

    Baza danych & Diagnostyka

    • Baza danych sterowników
    • Katalog kodów DTC
    • Przewodniki diagnostyczne & Pomiary
    • Analizator błędów AI
    • Aktualności

    Producenci ECU

    • Bosch
    • Continental
    • Delphi
    • Delco
    • Denso
    • Magneti Marelli
    • Siemens / VDO
    • Keihin
    • Temic

    Firma

    • O nas
    • Kontakt
    • Partnerzy warsztatów
    • Przewodnik wysyłki
    • Gwarancja
    • FAQ
    • Regulamin
    • Polityka prywatności
    • Mapa strony

    • Optymalizacja silnika
    • Naprawa sterownika
    • Klonowanie modułów
    • Zestaw wskaźników
    • SRS / Poduszka powietrzna
    • Immobilizer

    • Baza danych sterowników
    • Katalog kodów DTC
    • Przewodniki diagnostyczne & Pomiary
    • Analizator błędów AI
    • Aktualności

    • Bosch
    • Continental
    • Delphi
    • Delco
    • Denso
    • Magneti Marelli
    • Siemens / VDO
    • Keihin
    • Temic

    • O nas
    • Kontakt
    • Partnerzy warsztatów
    • Przewodnik wysyłki
    • Gwarancja
    • FAQ
    • Regulamin
    • Polityka prywatności
    • Mapa strony

    Odwiedź nas

    Gjuterigatan 29, Karlstad

    Zadzwoń do nas

    054-830 480

    Napisz do nas

    service@obdtuning.se

    © 2026 OBD Tuning Karlstad. Wszelkie prawa zastrzeżone.