VOLVO
ECM-P03392F - Crankshaft Position Sensor A Circuit Intermittent. General Signal Failures. Signal erratic
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
7 modeliS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Pokaż modele wg rocznika i silnika (20)
- Volvo S60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Tylko silnik: B4204T6
- Volvo S80 (2007–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Tylko silnik: B4164T
- Volvo V40 (2013–)2013Tylko silnik: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Tylko silnik: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Tylko silnik: B4164T
- Volvo V60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Tylko silnik: B4204T6
- Volvo V70 (2008–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Tylko silnik: B4164T, B4164T2
- Volvo XC60 (2009–)2010Tylko silnik: B4204T6
- Volvo XC60 (2009–)2011–2012Tylko silnik: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Tylko silnik: B4204T7
Co oznacza ten kod błędu?
The fault is recorded as intermittent, meaning it comes and goes, and it may not be present right now. The engine control module (ECM) monitors the signal from the crankshaft position sensor. The fault is stored when the signal is missing or incorrect, and the signal is described as erratic.
Możliwe przyczyny
- Contact resistance and oxidation in the connections
- Short circuit in the sensor wiring
- Sensor fitted incorrectly
- Damaged crankshaft position sensor
Co możesz zrobić
- 1If you have a diagnostic tool, start the engine and read the fault status. 'No fault found' means the fault is not active right now.
- 2Check that the fuses are intact.
- 3With the ignition off, check that the sensor connector is secure and free from oxidation and contact resistance.
- 4Use a multimeter to check that the sensor wires have no open circuit and are not shorted to ground (the body).
- 5Check that the sensor is correctly fitted and that no cable with high current draw lies too close to the sensor or its wiring. Such cables can disturb the signal.
- 6If you have a diagnostic tool, read the engine speed in live data during a test drive and check that the value is steady.
Objawy, które możesz zauważyć1
- No noticeable symptoms for the driver
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.