VOLVO
ECM-P034400 - Camshaft Position Sensor A Circuit Intermittent (Bank 1 or single sensor). General Failure Information. No sub type information
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Ten kod błędu ma różne znaczenie w zależności od modelu, rocznika lub silnika. Wybierz znaczenie, które dotyczy Twojego samochodu.
Dotyczy następujących modeli:
10 modeliS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Pokaż modele wg rocznika i silnika (36)
- Volvo S60 (2011–)2011–2012Tylko silnik: B5254T5, B6304T4
- Volvo S60 (2011–)2013–2014Tylko silnik: B5204T8, B5204T9, B5254T12, B5254T14, B6304T4
- Volvo S60 (2011–)2015Tylko silnik: B5204T8, B5204T9, B5254T12, B5254T14, B6304T3, B6304T4, B6304T5
- Volvo S80 (2007–)2007Wszystkie silniki oprócz: D5244T4, D5244T5
- Volvo S80 (2007–)2008Tylko silnik: B5254T6, B6304T2, B6324S, B8444S
- Volvo S80 (2007–)2009Tylko silnik: B5254T6, B5254T8, B6304T2, B6324S, B8444S
- Volvo S80 (2007–)2010Wszystkie silniki oprócz: B4204S3, B4204S4, B4204T6, D4204T, D5244T10, D5244T14, D5244T19
- Volvo S80 (2007–)2011Wszystkie silniki oprócz: B4164T, B4204S3, B4204S4, B4204T6, B4204T7, D5204T2, D5244T10
- Volvo S80 (2007–)2012Tylko silnik: B5254T10, B6304T4, B6324S4, B6324S5
- Volvo S80 (2007–)2013–2014Tylko silnik: B5254T12, B5254T14, B6304T4, B6324S4, B6324S5
- Volvo S80 (2007–)2015Tylko silnik: B6304T4, B6324S4, B6324S5
- Volvo V40 (2013–)2013–2014Tylko silnik: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V40 (2013–)2015Tylko silnik: B5204T8, B5204T9
- Volvo V40 Cross Country (2013–)2013–2015Tylko silnik: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V60 (2011–)2011–2012Tylko silnik: B6304T4
- Volvo V60 (2011–)2013Tylko silnik: B5204T8, B5204T9, B6304T4
- Volvo V60 (2011–)2014Tylko silnik: B5204T8, B5204T9, B5254T12, B6304T4
- Volvo V60 (2011–)2015Tylko silnik: B5204T9, B5254T12, B6304T3, B6304T4, B6304T5
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008Tylko silnik: B5254T6, B6304T2, B6324S
- Volvo V70 (2008–)2009Tylko silnik: B5254T6, B5254T8, B6304T2, B6324S
- Volvo V70 (2008–)2010Tylko silnik: B5254T10, B5254T11, B6304T2, B6324S, B6324S2, D4164T
- Volvo V70 (2008–)2011Tylko silnik: B5254T10, B5254T11, B6304T4, B6324S5, D4164T
- Volvo V70 (2008–)2012Tylko silnik: B5254T10, B6304T4, B6324S5
- Volvo V70 (2008–)2013–2014Tylko silnik: B5204T9, B6304T4, B6324S5
- Volvo V70 (2008–)2015Tylko silnik: B5204T9, B6304T4
- Volvo XC60 (2009–)2009Tylko silnik: B6304T2
- Volvo XC60 (2009–)2010Tylko silnik: B6304T2, B6324S, B6324S2
- Volvo XC60 (2009–)2011–2014Tylko silnik: B6304T4, B6324S4, B6324S5
- Volvo XC60 (2009–)2015Tylko silnik: B5204T9, B5254T12, B5254T14, B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2008Tylko silnik: B6324S
- Volvo XC70 (2008–)2009Tylko silnik: B6304T2, B6324S
- Volvo XC70 (2008–)2010Tylko silnik: B6304T2, B6324S, B6324S2
- Volvo XC70 (2008–)2011–2015Tylko silnik: B6304T4, B6324S4, B6324S5
- Volvo XC90 (2003–)2007–2010Tylko silnik: B6324S
- Volvo XC90 (2003–)2011–2014Tylko silnik: B6324S5
Co oznacza ten kod błędu?
The fault is recorded as intermittent, meaning it comes and goes, and it may not be present right now. The engine control module (ECM) reads the PWM signal from the camshaft sensor. The fault is stored when the signal is missing from time to time, or when the camshaft has too few segments over a set number of crankshaft revolutions. The code applies to the intake camshaft sensor on bank 1.
Możliwe przyczyny
- Camshaft sensor in the wrong position
- Damaged camshaft sensor
- Loose connections
- Contact resistance and oxidation in the connections
- Open circuit or short circuit to ground or supply voltage in the signal wire
- Camshaft sensor fitted incorrectly
Co możesz zrobić
- 1If you have a diagnostic tool, start the engine, raise the speed and read the fault status. 'Fault found' means the fault is permanent.
- 2Check that the fuses are intact.
- 3With the ignition off, check that the connector at the camshaft sensor is clean, secure and free from contact resistance and oxidation.
- 4Check that the camshaft sensor is correctly fitted and that the housing around it is not damaged, since that can affect its position.
- 5If your diagnostic tool shows it, read the camshaft sensor position or speed in live data while the engine runs.
- 6If the fault returns, have a workshop check the camshaft sensor and its signal wire.
Objawy, które możesz zauważyć5
- Engine is hard to start
- Check engine light (emissions warning lamp) is on
- Automatic engine start/stop does not work
- Car lacks power
- Car hesitates or jerks while driving
Na co może wpływać usterka3
- The ECM uses the crankshaft sensor signal instead
- Variable valve timing (VVT) control is blocked
- Camshaft control is switched off
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.