VOLVO
ECM-P034500 - Camshaft Position Sensor A Circuit (Bank 2). General Failure Information. No sub type information
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
7 modeliS60 (2011–), S80 (2007–), V60 (2011–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Pokaż modele wg rocznika i silnika (21)
- Volvo S60 (2011–)2011–2014Tylko silnik: B6304T4
- Volvo S60 (2011–)2015Tylko silnik: B6304T3, B6304T4, B6304T5
- Volvo S80 (2007–)2007–2009Tylko silnik: B6324S, B8444S
- Volvo S80 (2007–)2010Tylko silnik: B6324S, B6324S2, B8444S
- Volvo S80 (2007–)2011Tylko silnik: B6304T4, B6324S4, B6324S5, B8444S
- Volvo S80 (2007–)2012–2015Tylko silnik: B6304T4, B6324S4, B6324S5
- Volvo V60 (2011–)2011–2014Tylko silnik: B6304T4
- Volvo V60 (2011–)2015Tylko silnik: B6304T3, B6304T4, B6304T5
- Volvo V70 (2008–)2008–2009Tylko silnik: B6324S
- Volvo V70 (2008–)2010Tylko silnik: B6324S, B6324S2
- Volvo V70 (2008–)2011–2014Tylko silnik: B6304T4, B6324S5
- Volvo V70 (2008–)2015Tylko silnik: B6304T4
- Volvo XC60 (2009–)2010Tylko silnik: B6324S, B6324S2
- Volvo XC60 (2009–)2011–2015Tylko silnik: B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2008–2009Tylko silnik: B6324S
- Volvo XC70 (2008–)2010Tylko silnik: B6324S, B6324S2
- Volvo XC70 (2008–)2011–2015Tylko silnik: B6304T4, B6324S4, B6324S5
- Volvo XC90 (2003–)2005–2006Tylko silnik: B8444S
- Volvo XC90 (2003–)2007–2010Tylko silnik: B6324S, B8444S
- Volvo XC90 (2003–)2011Tylko silnik: B6324S5, B8444S
- Volvo XC90 (2003–)2012–2014Tylko silnik: B6324S5
Co oznacza ten kod błędu?
The engine control module (ECM) reads the gear wheel on the camshaft through the camshaft sensor. The code is set when the ECM counts too few segments over a set number of crankshaft revolutions. It applies to the intake camshaft sensor on bank 2, the cylinder bank at the rear.
Możliwe przyczyny
- Open circuit in the signal cable
- Signal cable short circuit to ground
- Signal cable short circuit to supply voltage
- Damaged camshaft sensor
Co możesz zrobić
- 1If you have a diagnostic tool, start the engine, raise the engine speed a few times and read the fault status. 'Fault found' means the fault is permanent.
- 2Check that the fuses are intact.
- 3With the ignition off, check that the connector at the bank 2 camshaft sensor is secure and clean.
- 4Use a multimeter to check that the signal wire to the bank 2 camshaft sensor has no open circuit and is not shorted to ground or supply voltage.
- 5If your diagnostic tool shows it, read the bank 2 camshaft sensor in live data while the engine runs.
- 6If the fault returns, have a workshop check the bank 2 camshaft sensor and its wiring.
Objawy, które możesz zauważyć5
- Car lacks power, especially when pulling away from standstill
- Car lacks power while driving
- Car hesitates or jerks during acceleration
- Car hesitates or jerks when slowing down
- Check engine light is on or behaves abnormally
Na co może wpływać usterka2
- The ECM uses the crankshaft sensor signal instead
- Camshaft control is switched off
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.