VOLVO
ECM-P034600 - Camshaft Position Sensor A Circuit Range/Performance (Bank 2). General Failure Information. No sub type information
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
7 modeliS60 (2011–), S80 (2007–), V60 (2011–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Pokaż modele wg rocznika i silnika (21)
- Volvo S60 (2011–)2011–2014Tylko silnik: B6304T4
- Volvo S60 (2011–)2015Tylko silnik: B6304T3, B6304T4, B6304T5
- Volvo S80 (2007–)2007–2009Tylko silnik: B6324S, B8444S
- Volvo S80 (2007–)2010Tylko silnik: B6324S, B6324S2, B8444S
- Volvo S80 (2007–)2011Tylko silnik: B6304T4, B6324S4, B6324S5, B8444S
- Volvo S80 (2007–)2012–2015Tylko silnik: B6304T4, B6324S4, B6324S5
- Volvo V60 (2011–)2011–2014Tylko silnik: B6304T4
- Volvo V60 (2011–)2015Tylko silnik: B6304T3, B6304T4, B6304T5
- Volvo V70 (2008–)2008–2009Tylko silnik: B6324S
- Volvo V70 (2008–)2010Tylko silnik: B6324S, B6324S2
- Volvo V70 (2008–)2011–2014Tylko silnik: B6304T4, B6324S5
- Volvo V70 (2008–)2015Tylko silnik: B6304T4
- Volvo XC60 (2009–)2010Tylko silnik: B6324S, B6324S2
- Volvo XC60 (2009–)2011–2015Tylko silnik: B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2008–2009Tylko silnik: B6324S
- Volvo XC70 (2008–)2010Tylko silnik: B6324S, B6324S2
- Volvo XC70 (2008–)2011–2015Tylko silnik: B6304T4, B6324S4, B6324S5
- Volvo XC90 (2003–)2005–2006Tylko silnik: B8444S
- Volvo XC90 (2003–)2007–2010Tylko silnik: B6324S, B8444S
- Volvo XC90 (2003–)2011Tylko silnik: B6324S5, B8444S
- Volvo XC90 (2003–)2012–2014Tylko silnik: B6324S5
Co oznacza ten kod błędu?
The code applies to the intake camshaft sensor on bank 2. The engine control module (ECM) counts the segments on the camshaft gear wheel, and the fault is stored when the count is wrong over two crankshaft revolutions, which is one camshaft revolution. The code does not say which type of fault it is.
Możliwe przyczyny
- Wiring or connector fault that comes and goes
- Camshaft sensor fitted incorrectly
- Damaged camshaft sensor
Co możesz zrobić
- 1If you have a diagnostic tool, start the engine and read the fault status. 'No fault found' means the fault is not active right now.
- 2Check that the fuses are intact.
- 3With the ignition off, check that the camshaft sensor connector is free from contact resistance and oxidation, and that the sensor is correctly fixed.
- 4Check that the wiring to the bank 2 camshaft sensor has no chafing or loose connectors, since a wiring fault can come and go.
- 5If your diagnostic tool shows it, read the bank 2 camshaft sensor in live data while the engine runs.
- 6If the fault returns, have a workshop check the camshaft sensor and its wiring.
Objawy, które możesz zauważyć4
- Car lacks power while driving
- Car hesitates or jerks during acceleration
- Car hesitates or jerks at steady speed
- Check engine light is on or behaves abnormally
Na co może wpływać usterka2
- The ECM uses the crankshaft sensor signal instead
- Camshaft control is switched off
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.