VOLVO
ECM-P035500 - Ignition Coil E Primary/Secondary Circuit. General Failure Information. No sub type information
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
6 modeliS60 (2011–), S80 (2007–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Pokaż modele wg rocznika i silnika (19)
- Volvo S60 (2011–)2011–2012Tylko silnik: B5254T5
- Volvo S80 (2007–)2007Wszystkie silniki oprócz: D5244T4, D5244T5
- Volvo S80 (2007–)2008Tylko silnik: B5254T6, B6304T2, B6324S, B8444S
- Volvo S80 (2007–)2009Tylko silnik: B5254T6, B5254T8, B6304T2, B6324S, B8444S
- Volvo S80 (2007–)2010Tylko silnik: B5254T10, B5254T11, B5254T8, B6304T2, B6324S, B6324S2, B8444S
- Volvo S80 (2007–)2011Tylko silnik: B5254T10, B5254T11, B5254T8, B8444S
- Volvo S80 (2007–)2012Tylko silnik: B5254T10
- Volvo V70 (2008–)2008Tylko silnik: B5254T6, B6304T2, B6324S
- Volvo V70 (2008–)2009Tylko silnik: B5254T6, B5254T8, B6304T2, B6324S
- Volvo V70 (2008–)2010Tylko silnik: B5254T10, B5254T11, B6304T2, B6324S, B6324S2
- Volvo V70 (2008–)2011Tylko silnik: B5254T10, B5254T11
- Volvo V70 (2008–)2012Tylko silnik: B5254T10
- Volvo XC60 (2009–)2009Tylko silnik: B6304T2
- Volvo XC60 (2009–)2010Tylko silnik: B6304T2, B6324S, B6324S2
- Volvo XC70 (2008–)2008Tylko silnik: B6324S
- Volvo XC70 (2008–)2009Tylko silnik: B6304T2, B6324S
- Volvo XC70 (2008–)2010Tylko silnik: B6304T2, B6324S, B6324S2
- Volvo XC90 (2003–)2005–2006, 2011Tylko silnik: B8444S
- Volvo XC90 (2003–)2007–2010Tylko silnik: B6324S, B8444S
Co oznacza ten kod błędu?
The code applies to ignition coil E, which is the coil for cylinder 5. It shows which coil is affected but not which type of fault it is. The engine control module (ECM) checks the coils' function through a separate diagnostic line.
Możliwe przyczyny
- Contact resistance and oxidation at the coil connector
- Signal wire short circuit to ground or supply voltage
- Open circuit in the signal wire
- Open circuit in the supply wire
- Diagnostic line short circuit to ground or supply voltage
- Damaged ignition coil
Co możesz zrobić
- 1If you have a diagnostic tool, start the engine and read the fault status. 'No fault found' means the fault is not active right now.
- 2Check that the fuses are intact.
- 3With the ignition off, check the connector to the ignition coil for cylinder 5 for contact resistance and oxidation.
- 4Use a multimeter to check that the wires to the ignition coil for cylinder 5 have no open circuit and are not shorted to ground or supply voltage.
- 5Check that the ignition coil is secure and not damaged.
- 6If the fault returns, have a workshop check the ignition coil for cylinder 5 and its diagnostic line.
Objawy, które możesz zauważyć5
- Engine misfires
- Check engine light (emissions warning lamp) is on
- Engine is not firing on all cylinders
- Car lacks power, especially when pulling away from standstill
- Car hesitates or jerks when slowing down
Na co może wpływać usterka1
- Closed loop control of lambda is blocked
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.