VOLVO
ECM-P045912 - Evaporative Emission System Purge Control Valve Circuit High. General Electrical Failures. Circuit short to battery
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
7 modeliS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Pokaż modele wg rocznika i silnika (20)
- Volvo S60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Tylko silnik: B4204T6
- Volvo S80 (2007–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Tylko silnik: B4164T
- Volvo V40 (2013–)2013Tylko silnik: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Tylko silnik: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Tylko silnik: B4164T
- Volvo V60 (2011–)2011Tylko silnik: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Tylko silnik: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Tylko silnik: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Tylko silnik: B4204T6
- Volvo V70 (2008–)2011Tylko silnik: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Tylko silnik: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Tylko silnik: B4164T, B4164T2
- Volvo XC60 (2009–)2010Tylko silnik: B4204T6
- Volvo XC60 (2009–)2011–2012Tylko silnik: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Tylko silnik: B4204T7
Co oznacza ten kod błędu?
The engine control module has registered that the signal from the EVAP valve is too high. The code is general and concerns an electrical fault. The causes are a signal wire short-circuited to supply voltage or a damaged EVAP valve.
Możliwe przyczyny
- The signal wire is short-circuited to supply voltage
- Damaged EVAP valve
Co możesz zrobić
- 1Check that the connector at the EVAP valve is fully seated and free from corrosion
- 2Look for chafing or pinch damage on the wire between the EVAP valve and the engine control module
- 3Use a multimeter to check that the EVAP valve is electrically intact. An open circuit or short inside the valve shows that it is damaged
- 4With a multimeter, check that the signal wire between the engine control module and the EVAP valve has no contact with supply voltage
- 5Replace a damaged EVAP valve, clear the code and road test. If the fault remains, have a workshop with diagnostic equipment check the wiring
Objawy, które możesz zauważyć1
- The malfunction indicator (check engine) light comes on or behaves abnormally
Na co może wpływać usterka1
- Control with two oxygen sensors (lambda sensors) is disabled
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.