VOLVO
ECM-P057900 - Cruise Control Multi-Function Input A Circuit Range/Performance. General Failure Information. No sub type information
Układ
Sterownik silnika (ECM)
Modele Volvo, których dotyczy ten kod błędu
Dotyczy następujących modeli:
5 modeliS60 (2011–), S80 (2007–), V70 (2008–), XC60 (2009–), XC70 (2008–)
Pokaż modele wg rocznika i silnika (13)
- Volvo S60 (2011–)2011–2012Tylko silnik: B5254T5
- Volvo S80 (2007–)2007–2008Tylko silnik: B5254T6
- Volvo S80 (2007–)2009Tylko silnik: B5254T6, B5254T8, D5244T10
- Volvo S80 (2007–)2010Tylko silnik: B5254T10, B5254T11, B5254T8, D5244T10, D5244T14, D5244T19
- Volvo S80 (2007–)2011Tylko silnik: B5254T10, B5254T11, B5254T8
- Volvo S80 (2007–)2012Tylko silnik: B5254T10
- Volvo V70 (2008–)2008Tylko silnik: B5254T6
- Volvo V70 (2008–)2009Tylko silnik: B5254T6, B5254T8, D5244T10
- Volvo V70 (2008–)2010Tylko silnik: B5254T10, B5254T11, D5244T10, D5244T14, D5244T19
- Volvo V70 (2008–)2011Tylko silnik: B5254T10, B5254T11
- Volvo V70 (2008–)2012Tylko silnik: B5254T10
- Volvo XC60 (2009–)2010Tylko silnik: D5244T10, D5244T14, D5244T16
- Volvo XC70 (2008–)2010Tylko silnik: D5244T10, D5244T14, D5244T16
Co oznacza ten kod błędu?
The ECM receives the signal from the front monitoring module (FSM) over the CAN network. The fault is stored when the signal from the FSM is faulty, and The code is also set by a CAN communication fault, or by a fault in the steering wheel module, the central electronics module, the brake control module or the transmission control module.
Możliwe przyczyny
- Open circuit in one of the CAN wires
- Short circuit between the CAN wires
- Internal fault in the ECM itself
- Temporary breaks or interference on one or both CAN wires on part of the network
- Contact resistance, oxidation or open circuit in connections
- The ECM is not intended for this car, for example a used module with different software or hardware
Co możesz zrobić
- 1Check that the fuses are intact
- 2If you have diagnostic equipment: read the CEM and other affected module fault codes, deal with them first, then clear this code
- 3If you have diagnostic equipment: read the fault codes in the front monitoring module (FSM)
- 4Check that the connectors on the CAN network are firmly seated and not corroded
- 5Use a multimeter to check that the CAN wires have no open circuit or short to each other
- 6If nothing is found, have a workshop check the CAN network and that the engine control module is intended for this particular car
Objawy, które możesz zauważyć2
- Cruise control does not work at all
- Cruise control does not engage
Na co może wpływać usterka2
- Cruise control is switched off
- Cruise control cannot be activated
Ogólne wskazówki dla właścicieli. Diagnostyka na samochodzie może wskazać inną przyczynę.